Hobby King Fire Phoenix - VERTIGO Rebel 90mm EDF Trainer
(For full disclosure: I am the original designer of the VERTIGO Rebel)
I know as of this writing, there are several of the Hobby King Fire Phoenix's out there.
It turns out this is a great trainer for the authentic more sophisticated, all Epoxy composite VERTIGO Rebel.
Guys are coming up with great ideas on how to set these up.
What I am doing here is building my Fire Phoenix more like the original VERTIGO Rebel 127mm sport jet seen here.
To keep things simple, I think I will stay with the fixed vertical stabs instead of the full flying rudders on the Rebel.
There is no design into the wings for the leading edge slats like the Rebel has.
I am going to make the full flying elevators like the Rebel has.
Others have opted to fix the horizontal stabs and cut in elevators.
As most of you know who are following the Fire Phoenix, BRuff has been having way too much fun with his.
At the field it has been called the "Baby Rebel" and "Little Richard"
More to come!
UPDATE 08/03/2013: Until now, one has ever seen a Fire Phoenix and VERTIGO Rebel together before.
Below are the comparisons.
The Rebel is all epoxy composite with vacuum bagged wings.
The Fire Phoenix is polyester with wood wings.
Last edited by wingspan100; Aug 03, 2013 at 09:26 PM.
Got the electric retracts and struts installed.
1) Turnigy Full Metal Servoless Retracts w/Steerable Nose Assembly (3mm pin)
2) 7075 Alloy Shock Absorbing Strut Set
I used a dremel to open the width of the landing gear rails to accept the electric retracts.
Be sure to test the operation of the electric gear before installing, just in case...
Then installed the struts after grinding the flat spots on the landing gear wires.
Next is the mounting of the 90mm EDF and motor.
Because of the larger battery, I positioned
The EDF further aft than the normal location.
The red cups are from WalMart, 4 for $1.
I had to extent the EDF mounting tabs with plywood.
It appears they made the opening for a 114mm EDF.
Attached the Mylar thrust tube.
90mm Haoye EDF
Walmart plastic cups 4 for $1
Still half the cost of some other 120mm jets.
The Rebel was originally deigned for 3D jet flying fitting a P-60 turbine.
Notice all the flying surfaces, Huge ailerons, full flying elevators and rudders.
Leading edge slats.
I'm not sure there is a 120mm EDF that will power a 3D flight yet.
The HK Fire Phoenix is just a cheap copy that flies very well.
This is why it makes a great trainer for those who will step up to the Rebel.
Do you have a thrust vectoring nossle for it?
Also I'm not sure there the same but your control horns look a lot like the ones that came with the 30cc GeeBee R3 powered by DLE55, Mine uses 2 of those horns with no issues but one flyer only used one horn and it broke on his 2nd flight
Can 5000mah 12 fit in the 120mm jet? Will you be doing a build on it?
Also what do the Leading edge slats do for you?
Thanks sweet jet
|Category||Thread||Thread Starter||Forum||Replies||Last Post|
|Discussion||Hobby King's Fire Phoenix EDF 1st flight||bruff||Electric Ducted Fan Jet Talk||56||Oct 14, 2014 08:51 AM|
|Sold||Rebel by Vertigo||1moparman1||Aircraft - Electric - Jets (FS/W)||0||Jul 14, 2013 07:15 PM|
|Sold||Rebel by Vertigo||1moparman1||Aircraft - Electric - Jets (FS/W)||22||Jul 05, 2013 07:22 PM|
|Discussion||FIRE PHOENIX 90MM EDF - composite||FOX ONE!||Electric Ducted Fan Jet Talk||9||Jul 23, 2012 11:03 AM|