Thread Tools
Jul 16, 2013, 01:36 AM
Registered User
Here, let me post another picture, sorry if it is low quality.
[URL=http://s452.photobucket.com/user/rickyaditya/media
I can't screw the carbon plate to the plastic motor mount because of the 3 motor wires.
Motor screwed to the three outer hole on the carbon plate, so it can't be reversed.
Sign up now
to remove ads between posts
Jul 16, 2013, 02:23 AM
Registered User
I see no problem in cutting the plate like you have shown, but there is room enough to let the wires go through the oval opening and into the boom
Jul 16, 2013, 02:54 AM
Albuquerque USA
Quote:
Originally Posted by mrqua View Post
Hi guys,
I'm currently building this frame using sunnysky X4108S 600KV.
Having trouble attach the motor to the mount cause the motor wire.
Can I do the modification on the carbon motor mounting like in the picture

So the wire can be put inside the carbon boom.
Thx for the suggestion.
I just check and it better to cut that part out so the cable can go through. You can force the cable without cutting the plate but that join motor wire will break sooner or later under vibration. So best is to cut that part off it doesn't affect anything that I can see
Jul 16, 2013, 03:36 AM
Registered User
Thanks for the reply
Let me post another pic (sorry if it is low quality) to show that I can't force the wire through the carbon plate opening

See the edge of the plate

Can not bend the wire to the bottom
Last edited by mrqua; Jul 16, 2013 at 03:42 AM.
Jul 16, 2013, 07:26 AM
Registered User
Who has stock of the 690? Checked a couple of the links from this thread but could not find stock at those sites. Thanks
Jul 16, 2013, 10:58 PM
Registered User
www.beevrc.com
Jul 16, 2013, 11:22 PM
Albuquerque USA
Quote:
Originally Posted by Lorisdem View Post
I rather burn my money than do business with them
Jul 17, 2013, 12:01 PM
Registered User
see the pics of the fy690S
Jul 17, 2013, 01:48 PM
Registered User
brifa's Avatar
A good sunnysky motor configuration to use with 5000mah 3S lipo??

i am testing it with these motors
Sunnysky 2212-13 kv980
http://www.foxtechfpv.com/sunnysky-2...980-p-384.html
with graupner 10x5 props
naza
no fpv stuff
but only tarot gimbal
well
only 5 minutes and it sucks 70% battery charge... doing a little flight and a lot of hovering

i would like to have a 10 minutes flight with also fpv stuff
please let me know
Jul 17, 2013, 01:54 PM
Albuquerque USA
Quote:
Originally Posted by brifa View Post
A good sunnysky motor configuration to use with 5000mah 3S lipo??

i am testing it with these motors
Sunnysky 2212-13 kv980
http://www.foxtechfpv.com/sunnysky-2...980-p-384.html
with graupner 10x5 props
naza
no fpv stuff
but only tarot gimbal
well
only 5 minutes and it sucks 70% battery charge... doing a little flight and a lot of hovering

i would like to have a 10 minutes flight with also fpv stuff
please let me know

it a waste to run any motor higher than 700 because it a big frame small props will have a hard time on the motor but putting bigger props on motor that wont able to swing it

the F550 yes you can going with the 9xx or 8xx kv but this thing is 680 or 690 so choose wisely guys

with the 690 you can easily swing 14" or maybe 15" i dont know about 15" but i know that 14" will do fine
Jul 18, 2013, 03:51 AM
Registered User
You should use 2814 700kv motors.
they fit perfectly on this frame.
Jul 18, 2013, 05:54 AM
Registered User
brifa's Avatar
Which prop for 3S lipo?
Quote:
Originally Posted by rahulvyas View Post
You should use 2814 700kv motors.
they fit perfectly on this frame.
Jul 19, 2013, 05:45 AM
Registered User
12" with 25A or 30A ESC

I use 4S with 11" and 25A plush!
Jul 20, 2013, 09:22 PM
Registered User
Just maiden 690 with:
Naza v2, sunnysky x4108s, flyfun 30, and 4s 4000.
I made mistake putting the 13' prop, the copter wobble all over the place, then stripping 2 prop. Try again with 3s, it successfully hover. Maybe tomorrow / day after tomorrow, will put the 12' prop and use the 4s. And then set the gain, cruise test, RTH test etc.
I will put the BeHolder gimbal, iOSD, and vtx later
Jul 22, 2013, 11:33 AM
Registered User
Name: DSC00199copy.jpg
Views: 595
Size: 145.0 KB
Description: Box
Last edited by Lorisdem; Jul 22, 2013 at 02:17 PM.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question GLB 20mm Carbon Fiber Center Plate +16pcs Tube Fixtures for 700-1000mm Hexacopter/Oct tormodnt Multirotor Drone Talk 5 Mar 09, 2014 12:18 AM
For Sale **New** Carbon Fiber Hexacopter 680 mm (Australia) LegendLength Aircraft - Electric - Multirotor (FS/W) 0 Apr 13, 2013 02:17 AM
Discussion ~800mm Carbon Fiber Hexacopter Frame serrated Multirotor Drone Talk 5 Feb 15, 2013 11:59 PM
For Sale HEXA X800-V6 Carbon Fiber Hexacopter frame Kit Go4it Aircraft - Electric - Multirotor (FS/W) 0 Dec 05, 2012 02:59 AM
Discussion strenght of 6mm square carbon fiber tube for hexacopter abcd123 Multirotor Drone Talk 0 Jan 27, 2012 03:01 PM