Thread Tools
Jan 30, 2004, 11:56 AM
Master of the Wind
AIR MOVER's Avatar
Yes I can fit you in..

I plan to use a small prop 3030's and the cox 3X1.2 ( hard to break) im still waiting on a working brushless esc.. Art I notice the 4020 at 3.25amps .. so should be around that amp draw with a 3030 .. I want to stay light as possible with 340mah kokams. I want to try the 3x1.2 for lower amps 2amps or so is what I would like for longer flights and still good speeds..should turn up the prop at or close to 30k
Sign up now
to remove ads between posts
Jan 30, 2004, 12:17 PM
characters welcome!
Mark Wood's Avatar
This has run its course in For Sale.
It will be in Product Announcements.

mw
Jan 30, 2004, 12:38 PM
Registered User
kushal_22's Avatar
Art Newland

Where are you getting these Props from?
Are they handmade or Bought?

Mal
Jan 30, 2004, 01:13 PM
Registered User
Air mover, Could u please ack the fact that I sent
you money a week or so ago for the 20 incher and let me know
when I can expect a shipment. Not to hurry you, just want
to know u got it and that I will too!

-A
Jan 30, 2004, 01:24 PM
Master of the Wind
AIR MOVER's Avatar
understand that.. pay pal normally sends a email to let you know .. but if there is any doubt just PM me and I will double check to make sure your in the loop.. I will continue to post updates on my work progress with the mass build ..getting there..=)
Jan 30, 2004, 01:36 PM
Registered User
I would like to try one. Send me billing information. Thank you.
Jan 30, 2004, 02:03 PM
CD-ROM Junkie
Art Newland's Avatar
kushal_22
direct drive props from GWS. i bought an assortment from all e rc
Jan 30, 2004, 02:10 PM
Master of the Wind
AIR MOVER's Avatar
Aero Micro has the 4040's ...
Last edited by AIR MOVER; Jan 30, 2004 at 04:18 PM.
Jan 30, 2004, 02:27 PM
Registered User
kushal_22's Avatar
agghh ok thanks
Mal
Jan 30, 2004, 04:26 PM
Master of the Wind
AIR MOVER's Avatar
Im not sure if everyone was aware.. but I do have a larger span racer on another thread.. here is the link to check it out..


https://www.rcgroups.com/forums/show...5&pagenumber=1
Jan 31, 2004, 10:01 PM
Registered User
I think we already discussed it per AOL IM, but please Brad, make sur eyou do have me in on this! I did go through Pay Pal... Mark
Feb 01, 2004, 12:27 AM
Master of the Wind
AIR MOVER's Avatar
yes Mark your good to go.!

update all the tail feathers are cut and now all I have to do is sand airfoils in them and hinge the elevators.

last task will be the fuselages.. =)
Feb 01, 2004, 03:02 PM
Master of the Wind
AIR MOVER's Avatar
here is a cd rom addition as a alternative to the gws 50
Feb 01, 2004, 04:07 PM
CD-ROM Junkie
Art Newland's Avatar

about ready to go


This is what I hope to use on mine
Feb 01, 2004, 04:36 PM
Master of the Wind
AIR MOVER's Avatar
You should be able to get away with not useing the prop adapter unless you use apc props like the 4.2X4.2 ...with the cut down shaft your motor should be good and light for wingloading purposes... my suggestion would be the gws hyper drive spinners with a gws 4040 .. it will send your plane vertical at over 45mph easy.. the cdrom upgrade is pure power and will keep you on your toes till the batts are depleted.. lucky we have throttle control lol.. Im useing a smaller prop a 3X1.2 cox prop to keep the amps down on the kokam 340's looking for about 3amps I will know as soon as my controler comes in for it. The one I had was bad out of the package... had the dreaded red led light on solid without arming..


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product NEW ImmersionRC Manta FPV Racing WING (Race PLANE) LexusFPV FPV Aircraft 120 Apr 03, 2017 02:02 PM