Thread Tools
Old May 02, 2013, 11:19 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Discussion

Martinez V3 board - wiring diagram


Just downloaded the manual. It didn't tell how to wire this thing. Searched everywhere and didn't find what I need.

Can anyone show me the wiring diagram for these. So far, I only knew where to put pitch motor and roll motor. Other than that, I'm gone!

Thanks!
Sign up now
to remove ads between posts
Old May 06, 2013, 02:16 AM
TheFernMan is offline
Find More Posts by TheFernMan
Too Many Thread Subscriptions
TheFernMan's Avatar
Something like this?

Name: ImageUploadedByTapatalk1367820976.666779.jpg
Views: 2675
Size: 129.1 KB
Description:
Old May 06, 2013, 02:59 AM
DYORD is online now
Find More Posts by DYORD
Registered User
Thanks... that's it.

So what should I put in A1 pitch and A2 roll?
Old May 06, 2013, 08:36 AM
TheFernMan is offline
Find More Posts by TheFernMan
Too Many Thread Subscriptions
TheFernMan's Avatar
those go to spare channels on your receiver. solder a pin to connect to it.
Old May 06, 2013, 01:54 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Quote:
Originally Posted by TheFernMan View Post
those go to spare channels on your receiver. solder a pin to connect to it.
So you mean i can control the pitch or roll with this board?
Old May 06, 2013, 03:11 PM
TheFernMan is offline
Find More Posts by TheFernMan
Too Many Thread Subscriptions
TheFernMan's Avatar
You're suppose to but i haven't tried it
Old May 06, 2013, 03:35 PM
wooden is offline
Find More Posts by wooden
Registered User
It's a manual override - the idea is it will continue to stabilize but it will be pointed up or down depending on how you override it. Not sure why you'd want to override roll but not my design...
Old May 06, 2013, 11:34 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Quote:
Originally Posted by wooden View Post
It's a manual override - the idea is it will continue to stabilize but it will be pointed up or down depending on how you override it. Not sure why you'd want to override roll but not my design...
Actually, i don't want to touch the roll. Just the pitch axis. I might want the camera point level or down but still stabilizing it to compensate the multirotor movements.

If you mean override, does it mean it won't stabilize that axis anymore?
Old May 14, 2013, 12:56 PM
DYORD is online now
Find More Posts by DYORD
Registered User
I just got my martinez v3 board. It came with 5 single cable connectors. The labels of the pins doesnt match the diagram above. Now i'm completely lost where to put what.

I also downloaded the manual. It really doesnt say there how to wire this thing.
Old May 14, 2013, 01:06 PM
TheFernMan is offline
Find More Posts by TheFernMan
Too Many Thread Subscriptions
TheFernMan's Avatar
are you talking about the sensor board to the gimbal controller?
Old May 14, 2013, 01:19 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Quote:
Originally Posted by TheFernMan View Post
are you talking about the sensor board to the gimbal controller?
Yes! Please help!
Old May 14, 2013, 01:26 PM
Askyvision is offline
Find More Posts by Askyvision
Albuquerque USA
Quote:
Originally Posted by DYORD View Post
Yes! Please help!
the manual have a clear picture how to hook up you didnt read the manual did you?

connect a1 to signal and GDN to ground on your Rx channel for ptich the 5 little cable you you get is to connect to your Gyro board that sit on the camera or camera tray.
Old May 14, 2013, 01:42 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Which manual are we talking about? I downloaded mine from witespy website.

Got the manual from here:

https://www.rcgroups.com/forums/atta...mentid=5689722
Last edited by DYORD; May 14, 2013 at 01:47 PM.
Old May 14, 2013, 01:42 PM
TheFernMan is offline
Find More Posts by TheFernMan
Too Many Thread Subscriptions
TheFernMan's Avatar
both the sensor board and the gimbal controller have GND, 5+(VCC), SCL, SDA

Connect those together. the other pins are not needed.



Heres a picture i found
Old May 14, 2013, 01:52 PM
DYORD is online now
Find More Posts by DYORD
Registered User
Thanks for that! Can someone tell me where to download the correct manual? Thanks!!


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Octocopter Wiring Diagram nikizwan Multirotor Talk 0 Apr 29, 2013 09:06 PM
Help! Brushless Gimbal V3.0 Controller Module w/ Sensor (Martinez)setBru Fassett DIY Electronics 0 Apr 21, 2013 01:48 AM
Discussion Wiring diagram for basic quad attached, let me know if it is correct. loac1111 Multirotor Electronics 10 Jan 22, 2013 10:59 AM
Discussion Wiring Diagrams? loac1111 Multirotor Electronics 3 Jan 19, 2013 03:49 PM
Discussion Please review my FPV quad wiring diagram schott1984 FPV Talk 9 Jan 04, 2013 10:38 PM