Thread Tools
Old Feb 23, 2013, 08:18 PM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Build Log

FPV Wing Builds (EPP 38"-48"-60") SweepWings


Hi guys,

I picked a name that will fit what I'm doing =) "SweepWings" I think it sounds good =)


(PM me for mor info sweepwingsrc@gmail.com)

(38" Flinch) (Prototype) (is no more)
(New 37" Flinch) Done testing
SweepWings Flinch quick run (4 min 21 sec)


(48" Juggernaut) Done Testing
SweepWings Flown with dragon link (4 min 30 sec)

or if you have Facebook I post updates on my builds. Facebook/SweepWings


(new 60" Behemoth) Almost done, few testers out
SweepWings Behemoth FPV Wing (8 min 7 sec)

SweepWings Behemoth Hugging the ground (2 min 43 sec)


Dreadnought 81.5 Beta
SweepWings "Dreadnought" 81.5" maiden (2 min 23 sec)


Payload test with bloopers
Payload test Flown with dragonlink (4 min 3 sec)


**** Instagram*****
Juggernaut 90+ mph run
https://instagram.com/p/2zC8DBzF85/


************* ALL WINGS HAVE BEEN TESTED TO OVER 100mph ***************


I wanted to post this for guys looking for a small wing platforms for FPV flights. The idea was to make a wing that can carry a HD video camera (Gopro) to record Vacations, day trips and spots that are hard to get to. I fell in love with wings due to the low down time on crashed and setups. I own alot of wings that i have bought from many vendors online and they seem to be missing some thing.....(ZII, Grim Reaper, Deep Reaper XL, Black knight) All good wings!! I am not downing the other wings at all. But for me, i wanted Payload, Agile, simple setup and tough....in HD =) It has taken me along time to get the prototypes done and to the point they are at now. So i'd like to share with everyone what I have done. Each Wing is HAND cut on a hot wire table that was made for me by a friend "Snipeworm" Big thanks to him. They are not 100% perfect, it's hard work to cut 1.3 and 1.9 EPP. As of right now im working on video of my flights today and kids are calling for me. So here are the pictures of what i have so far. =)


Thanks,
Ruben

PM me for more info sweepwingsrc@gmail.com =)
RCG Plus Member
Last edited by RUBNorris; Aug 27, 2016 at 02:38 PM. Reason: Name of wings
Sign up now
to remove ads between posts
Old Feb 24, 2013, 12:05 AM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Prototype "Flinch" 38"

FPV Wing "Flinch" Flight Video (2 min 14 sec)



Juggernaut 48"

FPV Wing "Juggernaut" for HD flights (0 min 0 sec)
RCG Plus Member
Old Feb 24, 2013, 12:21 AM
Jayshergill is offline
Find More Posts by Jayshergill
Registered User
I like both wings I was so surprised to see the wing "Flinch" carrying gopro on just a 2cell lipo very impressed.

I'm defiantly liking the wing "Juggernaut". Seems like it can carry more payload.

Got to wait for a calmer day so windy... Lol...
Old Feb 24, 2013, 09:55 AM
fnffishcore is offline
Find More Posts by fnffishcore
Registered User
fnffishcore's Avatar
Looks good man, congrats! I love that you incorporated the original GoPro case in the design; it's already the best protection you can get for your expensive camera, so why not use it!?

I'm not even gonna ask how much you'll be selling these for... The last thing I need is another wing to carry my GoPro... ESPECIALLY a compact wing that I can easily fit in my car...............
Old Feb 24, 2013, 07:10 PM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Quote:
Originally Posted by fnffishcore View Post
Looks good man, congrats! I love that you incorporated the original GoPro case in the design; it's already the best protection you can get for your expensive camera, so why not use it!?

I'm not even gonna ask how much you'll be selling these for... The last thing I need is another wing to carry my GoPro... ESPECIALLY a compact wing that I can easily fit in my car...............
LOL Thank you! There cheap. I just dont know how to ship them. Juggernaut 48" $160 build for everything but Batts and RX. Almost gone testing =)
RCG Plus Member
Old Feb 26, 2013, 11:12 AM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Ground video of the 38"  "Flinch"


Flinch FPV Wing Ground video (6 min 38 sec)







Ground video of the 48"  "Juggernaut"


Juggernaut FPV Wing Ground Video (3 min 22 sec)
RCG Plus Member
Old Feb 26, 2013, 11:40 AM
viper522 is offline
Find More Posts by viper522
Registered User
Quote:
Originally Posted by RUBNorris View Post
I just dont know how to ship them
From your pictures I'm guessing the Flinch will fit in a USPS Priority Mail Large Flat Rate box dim. 23-11/16" x 11-3/4" x 3". $17 for 2-3 day service anywhere in the USA. The Juggy might be a tight fit. Disassembled, of course (wing halves, center section, elevons).

http://postcalc.usps.com/Default.aspx
Old Feb 26, 2013, 01:21 PM
fnffishcore is offline
Find More Posts by fnffishcore
Registered User
fnffishcore's Avatar
Quote:
Originally Posted by RUBNorris View Post
LOL Thank you! There cheap. I just dont know how to ship them. Juggernaut 48" $160 build for everything but Batts and RX. Almost gone testing =)
I reeeeeeeeally shouldn't be asking, but what about selling just the cores and perhaps lam? Also, are the bays pre-cut as well? I have a 3530-1700KV motor and some servos looking for a new home...
Old Feb 26, 2013, 02:21 PM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Quote:
Originally Posted by viper522 View Post
From your pictures I'm guessing the Flinch will fit in a USPS Priority Mail Large Flat Rate box dim. 23-11/16" x 11-3/4" x 3". $17 for 2-3 day service anywhere in the USA. The Juggy might be a tight fit. Disassembled, of course (wing halves, center section, elevons).

http://postcalc.usps.com/Default.aspx

Id have to make sure the mail take good care of it. Tons of bubble wrap. If some
one really wants one, ill look into it. But the jugg would cost more i think? Homedeeepow has some large boxes. Ill ceep my eyes peeled.
RCG Plus Member
Old Feb 26, 2013, 02:32 PM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Aybe
Quote:
Originally Posted by fnffishcore View Post
I reeeeeeeeally shouldn't be asking, but what about selling just the cores and perhaps lam? Also, are the bays pre-cut as well? I have a 3530-1700KV motor and some servos looking for a new home...

Eh no worrys. Cores and lam maybe. The cores are never perfect due to them being cut by me.... A noob wing cutter. Lol.. i sand them into shape and make sure both sides are even. My arms get tired so alittle imperfetions are noticable. Maybe cores latter on when i get better. I need a better way to cut them.
Bays are not precut. I do all layout every time i make a wing. I need more help. Lol
RCG Plus Member
Old Feb 26, 2013, 02:35 PM
viper522 is offline
Find More Posts by viper522
Registered User
Quote:
Originally Posted by RUBNorris View Post
Id have to make sure the mail take good care of it. Tons of bubble wrap. If some
one really wants one, ill look into it. But the jugg would cost more i think? Homedeeepow has some large boxes. Ill ceep my eyes peeled.
The beauty of Flat Rate is if it fits, it ships! So as long as the Jug fits in the flat rate box, it doesn't cost any more to ship than the smaller Flinch kit. Shouldn't have to pad the box too much, you're shipping dense foam, that's what packing material itself is made from LOL
Old Feb 26, 2013, 02:48 PM
postalflyer72 is offline
Find More Posts by postalflyer72
Everything is Upgradeable.
Looks just like a mwc black night 49"
Old Feb 26, 2013, 03:02 PM
viper522 is offline
Find More Posts by viper522
Registered User
Quote:
Originally Posted by postalflyer72 View Post
Looks just like a mwc black night 49"
except this one is closer to shipping
Old Feb 26, 2013, 03:07 PM
RUBNorris is offline
Find More Posts by RUBNorris
New Beeeeee
RUBNorris's Avatar
Quote:
Originally Posted by postalflyer72 View Post
Looks just like a mwc black night 49"
Close to it. About 1inch wider and 1/2" thicker. Its out ot production now so i had to make my own wing.
RCG Plus Member
Old Feb 26, 2013, 08:24 PM
postalflyer72 is offline
Find More Posts by postalflyer72
Everything is Upgradeable.
You still made copies of a wing design that belongs to a company. They closed shop and that gives you the right to copy? Not to mention the black beauty cut properly was 40.00. I sent Jeff and mwc the link. It's up to him now if he has any issues with this.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold 3DHS EPP 38" SLICK - LPU in Houston Low_N_Slow Aircraft - Electric - Airplanes (FS/W) 10 Jan 10, 2013 12:23 PM
Gallery Scratch build EPP wing for fast FPV catching up with the winds tushev FPV Talk 4 Oct 18, 2010 11:32 AM
Build Log Build Log - STARFIRE! Mc Clain Wing Cores 48" virgin foam and EPP pval3 Flying Wings 75 May 28, 2009 11:36 PM