Originally Posted by Gregor99

With the latest firmware there is now a better way to charge 1s cells. There were two new 1s presets added for the PL6 and PL8. These do not require balance leads. Once the new firmware is loaded, select open file to preset on an open slot and select the new 1s presets from the LiPo folder. Post 1 has been updated.

Hey Gregor, was this firmware released recently? I believe I am running 1.10 or something along those lines. I do have the small 1s/2s unbalanced charge preset which I use to charge them via a paraboad and jst adaptor. What Im curious about is how I can setup a small 1s unbalance storage charge where it will charge/discharge to say 3.86

Guess I could copy that small non balance charge preset and just set the limit to 3.86.

Originally Posted by Mr.Aaron

Hey Gregor, was this firmware released recently? I believe I am running 1.10 or something along those lines. I do have the small 1s/2s unbalanced charge preset which I use to charge them via a paraboad and jst adaptor. What Im curious about is how I can setup a small 1s unbalance storage charge where it will charge/discharge to say 3.86

Guess I could copy that small non balance charge preset and just set the limit to 3.86.

The firmware update was released recently. You could use the unbalanced preset and change it use the storage profile. But I would just use the new presets. That what we made them for.

Originally Posted by Gregor99

The firmware update was released recently. You could use the unbalanced preset and change it use the storage profile. But I would just use the new presets. That what we made them for.

Will see about installing the new update, didn't know there was one but will check it out and see the new presets.

*update* I already had 1.10 which it shows as the latest firmware. I did do the update library preset but don't see any 1s/2s unbalanced storage charge/discharge preset.

1.11 is the latest firmware. The new presets are not in the regular preset library. Once the new firmware is loaded, select open file to preset on an open slot and select the new 1s presets from the LiPo folder.

Originally Posted by Gregor99

1.11 is the latest firmware. The new presets are not in the regular preset library. Once the new firmware is loaded, select open file to preset on an open slot and select the new 1s presets from the LiPo folder.

Finally got 1.11 loaded, had a random popup that said there was a newer version then it downloaded it and got it all installed. Went to the file open and then went to the "generic lipo" folder but don't see a 1s storage charge. I did try and load up the storage charge file attachment in your first post but when I try and load it onto my pl6 I get a duplicate error.

Appreciate all the help greg, this is my first time with updating my charger and setting presets as I usually use the presets it came with. But did download the manual for it to give a read thru.

Try this:

From the file menu select
1) FMA Default Presets
2) Open file to preset ##
3) The file dialog opens. Click on the Generic LiPo folder.

The new 1s presets are at the top of the list.

Originally Posted by Gregor99

Try this:

From the file menu select
1) FMA Default Presets
2) Open file to preset ##
3) The file dialog opens. Click on the Generic LiPo folder.

The new 1s presets are at the top of the list.

Hey Gregor,

I did a screenshot of my "generic lipo" folder as I figured that would be best to show you.

I can't make out the screen. But I take it you are showing me the presets are not in the folder. For this double check that you are using selecting "FMA Default Presets" from the file menu.

If that does not help, search your harddrive for the file:
"LiPo 1s no nodes High Power.PS6"

If you find it, note the path and use that in the CCS when opening the preset.

Originally Posted by Mr.Aaron

Hey Gregor,

I did a screenshot of my "generic lipo" folder as I figured that would be best to show you.

Did you get the 1s presets working? If not, you can try unistalling the CCS and re-installing it from http://www.revolectrix.com/new_appli..._software.html

Originally Posted by Gregor99

Did you get the 1s presets working? If not, you can try unistalling the CCS and re-installing it from http://www.revolectrix.com/new_appli..._software.html

Hey gregor, sorry for the late reply but I managed to get it working. I now have the 1s/2s unbalanced storage that will charge or discharge to storage level which is nice. Thank you again for all the help, this will make it a lot easier to take care of my smaller packs.

select preset 7 ,all brand storage charge >18min elapse monitoring cell voltage have not change

Cell voltage? Charge or discharge mode? Internal or regen discharge? Can perform a discharge with one of the other presets. Also when starting the cycle if you select "monitor", that's all it does, simply report the cell voltages. Useful for checking the voltage of packs is all that is required.

Hello, i need help
I bought the revolotrix charger and the MPA adaptor, but I have a problem, when I connect two batteries 6s the charger detects 7s! I have tried all by many ways. Now I'm trying to change the connection to XH and I find that my charger don't have the option to change it. I have made all correct, but the charger don't have the option to select the connection type.
Thanks

Originally Posted by sergiocruz

Hello, i need help
I bought the revolotrix charger and the MPA adaptor, but I have a problem, when I connect two batteries 6s the charger detects 7s! I have tried all by many ways. Now I'm trying to change the connection to XH and I find that my charger don't have the option to change it. I have made all correct, but the charger don't have the option to select the connection type.
Thanks

If you have the CCS (Charge Control Software) it is easy. I presume you do not have CCS. I recommend you get the FUIM3 interface and install CCS on your computer. It makes making changes to your charger very easy.

But to make the selection manually do the following:

Press INC and DEC together.
Press INC until Charger Options is displayed.
Press ENTER until Node Connector is displayed.
Press INC until XH/EH Wiring is displayed.
Press and hold Back to exit the Options.

It will pay to explore the rest of the settings available.

Glen

I'm trying to download the FUIM3 driver for the Powerlab 6 and a window pops up saying "The requested operation requires elevation". Any help?