Thread Tools
Sep 20, 2013, 04:19 AM
Registered User

Got it taken care of


Quote:
Originally Posted by hellafilming
I got a reply from flydunio and it was a mistake, new guy in the office. I appreciated the quick response, now we will see how long it takes to get here. So far so good on customer service.
They guys at Flydunio got the replacement boards out quick and nice. I am happy with their customer service.
Sign up now
to remove ads between posts
Sep 20, 2013, 04:56 AM
Registered User
Can anybody help: I have bought Spektrum SX7s and AR8000 to command gimbal. The rest of th model is working properly but the gmbal doesnt react at all. Previously i used a 4 channel tx/rx and that worked fine. Is there some setting in the board I need to change for it to listen to the AR8000?
Help is appreciated.
Sep 20, 2013, 06:27 AM
Registered User
does the alexmos board from Flyduino come with all the pins soldered ? sorry for asking but with solder I always do a mess
Sep 20, 2013, 08:03 AM
Ken's CAD Models
dz1sfb's Avatar
Quote:
Originally Posted by godwisper
does the alexmos board from Flyduino come with all the pins soldered ? sorry for asking but with solder I always do a mess
The 2 axis board does, but the 3rd axis board requires you to solder them.

Ken
Last edited by dz1sfb; Sep 20, 2013 at 10:02 AM. Reason: typo
Sep 20, 2013, 09:41 AM
Registered User
I think E-Copter and Fabien are deads.....

Pré-order start on february and - at almost - end of september nothing yet!
Sep 20, 2013, 11:57 AM
Registered User
Sorry I haven't kept up to date with the thread, but what is the difference with the V2 and the V3? They both function just the same just the V3 has the 3rd axis with the main board?
Sep 20, 2013, 02:45 PM
Registered User
Panza's Avatar
Quote:
Originally Posted by TonyTypeS
Sorry I haven't kept up to date with the thread, but what is the difference with the V2 and the V3? They both function just the same just the V3 has the 3rd axis with the main board?
yes
and some new components
Sep 20, 2013, 02:52 PM
by Alary Design
Photoship One's Avatar
Case design nearly finished for Viacopter with 3 axis.

USB extension for flush mount mini USB, pushbutton in side of case, plastic standoffs for 3 axis board. Holes in side to allow for power & rc control wires to exit.

Magpul fans may notice and like the Pmag style rounded rectangle insets.
Last edited by Photoship One; Sep 20, 2013 at 07:07 PM.
Sep 20, 2013, 03:34 PM
Registered User
flytahiti's Avatar
you have to sell those boxes !!!!!!!
Sep 20, 2013, 10:24 PM
Registered User
Quote:
Originally Posted by Panza
Hi

I tried Alexmox 3axis extention board on a Alexmoss copy, it works with.
I have built th brushlessgimbal.com gimbal with GBM 5208 150T
Can anybody give me the PID with this motors ?
Thanks
you have any luck with this?
Sep 20, 2013, 10:39 PM
Registered User
Quote:
Originally Posted by highviz
It just sounds like the c of g of the mount is not balanced around the yaw axis, so as you pitch the MR, gravity is overriding the stabilisation. Alternatively, if it only happens at speed, there is an aerodynamic effect resulting in a similar problem....

When hanging from a single point, getting a good yaw C of G can be tricky if there is any flex in the gimbal, as it naturally acts like a pendulum when you tilt it....

Malcolm
Thanks Malcolm. I've tried balancing it as best as I can, and I also lifted the camera as high as I could to help fend off this pendulum effect. I think I may have something that is workable - getting a flight up tomorrow to test it. I may just need to go with a bigger motor - using the iPower 5206 now.
Sep 21, 2013, 01:44 AM
Registered User
Panza's Avatar
Quote:
Originally Posted by aonavy
you have any luck with this?
yes and no. I stop use the copy (drotek) because there is no yaw control.
i used original alexmos card
the motor are good, execpt for the yaw. even at power 170, its a little less for the yaw.
Sep 21, 2013, 05:56 AM
Registered User
Salocin's Avatar
Quote:
Originally Posted by nisouck
I think E-Copter and Fabien are deads.....

Pré-order start on february and - at almost - end of september nothing yet!
Fabien, please answer my pm or email.
Sep 21, 2013, 07:57 AM
Registered User
Is it possible to get 3D of both AlexMos boards (normal+pan extension), it will make nicer overall model of gimbal

Please PM me

Thanks!
Jure
Sep 21, 2013, 02:57 PM
Registered User
Has anyone been able to get the "Yaw Offset" feature within in Follow Mode to function so as to be able to center the camera on the yaw axis? I have the latest FW and GUI but no luck with it. I have been using a lever on my TX as a work-around but would much prefer to use this Offset Yaw feature. I have tried just about everything but cannot get my Yaw axis to respond to any of the changes I make. Does anyone have a tip on how to make this work?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Mini-HowTo Super Simple Gimbal - SSG - KK2.1 & OpenPilot support crezzee Aerial Photography 1674 Apr 08, 2017 12:07 PM
Yippee! Simple Brushless Gimbal Controller--FPV MODEL fpvmodels Multirotor Drone Talk 3396 Dec 26, 2014 06:23 PM
Discussion A very simple camera-gimbal for Gaui 330xs babanan Multirotor Drone Talk 2 Oct 09, 2013 08:46 AM