Shop our Airplanes Products Drone Products Sales
Thread Tools
Jan 18, 2013, 07:45 PM
Registered User
Build Log

TG Interceptor


I picked the TG Interceptor as my winter project. Wood Sheeting is ordered and I hope to have it on the bench soon. I am undecided on what power system to use.

I have Jet Fan V2 90mm nib and I have a dynamax fan that I could convert to electric.

Jet Fan in the picture looks lost in the fuse. I plan on using an 11s 5000 pack.

Will the Jet Fan produce enough power or I am better off with a Dynamax set up ?

I build light.
Sign up now
to remove ads between posts
Jan 18, 2013, 07:49 PM
Registered User
I would think the dynamax would be better here. That is a huge airframe.
Jan 18, 2013, 07:58 PM
High Dynamic Thrust
stoneenforcer's Avatar
dyna for sure. the lil 90mm would need to fly wot all the time.
Jan 18, 2013, 09:37 PM
Registered User
jimm1962's Avatar
Nice kit, wish they still made it. Last I heard was that Dynamic Balsa picked up Top Gun Jets kits and were going to start bringing them out again. I believe they may have the F-15 out. Did the bring the interceptor out again?
Jan 18, 2013, 10:37 PM
Registered User
thats funny goforit,I think the dynamax would be best. Paul
Jan 18, 2013, 11:49 PM
Just having fun before I die!
BadLemon's Avatar
Rainer put a jetfan 90 into a F-86 the same size as a BVM F-86 . The setup he put in it produced about 11 pounds of thrust. Also Rainer has stated they are work on larger fans in the 110 to 130 range.
Feb 02, 2013, 07:42 PM
Registered User
Managed to find some building time and installed the fuse formers and nose gear bulkhead. Nose gear steering servo is installed. West Coast epoxy mixed with chopped fiberglass was used to glue in the formers.

Retracts I plan to use Spring Air with Robart Struts.

Tommorrow I plan on installing the intake duct work and dynamax fan.
Feb 03, 2013, 02:53 PM
Registered User
I designed the interceptor. It was designed for the dynamax fan to begin with. It will drop right in. You should see about a 4lbs increase in thrust over the slimer version.
Good luck on the build
Take Care
Marty Snell.
Feb 03, 2013, 05:38 PM
Registered User
Managed to install duct work today. 2 hours of trimming and fitting, the end result was worth it. Turned out nice.

Converting one of my ICDF to electric. New fan shroud , and Tam's Motor housing converison kt is order. I am undecided on what motor to order for a 11s set up.
Feb 04, 2013, 10:42 AM
Registered User
A10pilot's Avatar
Are you going to convert the Dynamax or use a different fan? I have converted a number of the Dynamax fans and the conversion works very well. I am getting about 15 lbs thrust on 12S with a 630KV outrunner @120 amps and 5+KW. These are wonderful flying planes. I am sure you will really like.

Progress looks great.

Ed
Feb 04, 2013, 01:04 PM
Hey Ya'll!! Watch THIS!!
Michael Paxton's Avatar
Just a heads up:

https://www.rcgroups.com/forums/show...16&postcount=1
Feb 04, 2013, 06:59 PM
Registered User
Quote:
Originally Posted by A10pilot
Are you going to convert the Dynamax or use a different fan? I have converted a number of the Dynamax fans and the conversion works very well. I am getting about 15 lbs thrust on 12S with a 630KV outrunner @120 amps and 5+KW. These are wonderful flying planes. I am sure you will really like.

Progress looks great.

Ed
Ed

Converting a Dynamax fan. Tam's Center housing conversion was delivered today.
New outer fan shroud is on its way and couple new fan blades.


Thanks

Dennis
Feb 04, 2013, 10:41 PM
Registered User
Fan is installed. I drilled oversize holes in the mounting plate. Made up shims from 1/32 plywood and nut plates. I will be able to move the fan around to get it centered up perfectly in the duct work.
Feb 04, 2013, 11:55 PM
Registered User
Hey go4it keep your cg in mind, to get a good balance in my interceter I had to mount the fan back just in front of the rear former,you will need. To extend. The intake, just a heads up. Paul
Feb 05, 2013, 06:37 AM
Registered User
Quote:
Originally Posted by eazyp2
Hey go4it keep your cg in mind, to get a good balance in my interceter I had to mount the fan back just in front of the rear former,you will need. To extend. The intake, just a heads up. Paul
Thanks Paul

I was considering mounting the servos in the tail to help move the cg aft. I will go with your advice and move the fan aft.

Thanks for your help !

Dennis


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! ITC Bladerunner Interceptor Gopher Coaxial Helicopters 2 Jan 09, 2013 08:23 PM
Discussion New TG-3/TG-3A at 2.1 meters mmartin55 Scale Sailplanes 1 Oct 16, 2006 11:07 PM
FS: Who want's an X-Wing interceptor? harryo Aircraft - Electric - Airplanes (FS/W) 6 Dec 02, 2004 07:57 AM
Interceptor For Sale mirageman2005 Aircraft - Fuel - Airplanes (FS/W) 0 Apr 07, 2003 01:40 AM