Her name is "Christine" - RC Groups
Thread Tools
Jan 06, 2013, 02:45 PM
Registered User

Her name is "Christine"

After many years of working on this, I finally just spent a few weeks working on it and got it done. Thought I'd share it with the micro car crowd, since we don't really have a scale car forum...

Probably one of my favorite movies of all time is Christine, based upon the Stephen King novel. In case you're unfamiliar, it's about a possessed 1958 Plymouth Fury that ends up killing the adversaries of its owner. I've always thought that car was perhaps one of the most beautiful from the 1950's, and ever since buying a Kyosho Mini Z MR-01 back in the late 90's, thought Christine would be a good custom body project. The problem was, there were no 1958 Fury kits to start from back then.
Last edited by PRND21; Jul 01, 2015 at 01:58 PM.
Sign up now
to remove ads between posts
Jan 06, 2013, 02:52 PM
Registered User
Well, that eventually changed, as I found a couple of these AMT/Ertl 1/25 1958 Belvederes (identical body to the Fury) on a popular auction site. Trouble was, this was long after the original Mini Z stopped working due to the interference prone AM radio. The chasses was still mostly good, however.
Jan 06, 2013, 02:57 PM
Registered User
I don't have more pics from this process unfortunately, but this was probably the most tricky part- actually aligning the body to be proportionate to where the wheels rest. This is done by extending the Mini- Z chasses. I used a piece of that springy aluminum plate sandwiched with a trimmed old credit card plastic. I will probably change this to making an extension out of G-10 fiberglass, then adding the H-plate to the end of the extension, but for now it works fine. Note the Audi TT rims from the original Mini Z the way I bought it. (That body also was the donor for the body mounts) These wheels had to go...
Last edited by PRND21; Jan 06, 2013 at 04:08 PM.
Jan 06, 2013, 03:06 PM
Registered User
I haven't built or painted an actual plastic model since I was about 14, so this part was pretty tough. Painting alone was a good reminder as to part of the reason why I no longer build models; it's a pain. Lots of wet sanding, and polishing, repainting, etc. I've never used that chrome bare metal foil before either, but it was a "must have" on this one. The paint used was Testors Laquer, but clear coat was Rustoleum Lacquer. Figured the thicker clear would be best for the occasional bang or scrape into the base board or chair. Also to address that, was the use of some carbon fiber stripping around the body attachment points, a lot was used up front (not pictured, behind the radiator housing.)
Last edited by PRND21; Jan 06, 2013 at 04:06 PM.
Jan 06, 2013, 03:15 PM
Registered User
One of the other big problems was how to have scale wheels. I don't race, and truth be told, really don't do a whole lot with RC cars anyway. I just wanted the model to be drivable, yet fun, and retain its scale look, and look nice on a shelf. This meant using the included "pizza cutter" car model tires, and somehow finding a way to retain the stock hubcaps that came with the kit. Fortunately, Atomic Mods sells these plain dish rims for the mini z that made the scale white wall wheels possible. With a little grinding, the model car tires fit perfectly over the rims, and grinding the inside of the hubcaps out allowed them to fit nicely over the nylon wheel nut without any obstruction. The included plastic "whitewalls" that came with the kit were sanded down until they just about "clicked" into the dish rim, allowing the hubcap to be tack glued in place for easy removal when doing maintenance.
Last edited by PRND21; Jan 06, 2013 at 04:18 PM.
Jan 06, 2013, 03:25 PM
Registered User
Next, I had to turn my attention to the chassis. I mentioned that the AM radio no longer works; radio interference must be way worse in 2013 than it was in 1999, with all the cell phones, blue tooth accessories, household electronic devices, etc. I suppose a better alternative (and might do in the future) would've been to buy a newer, Kyosho MR-03 chassis for this project, but they are crazy expensive. It was cheaper to buy a Losi Micro rock crawler, pull out its combined 2.4 receiver/esc, then wire it to the Kyosho steering servo. I almost forgot, that was a hurdle as well. I tore an old Futaba servo apart, and was able to wire it into the existing Kyosho pot to convert their 4 wire servo into a three wire. (I have a thread on here about how to do that somewhere.) This makes it possible to use any radio with the mini z, and, provides the added benefit of being able to power the lights from a Y harness. However, an MR-03 still sounds appealing. I'm running it on a 7.4 Lipo- gives plenty of power for the extra heft. Of course, this car would not be complete without lights. So, I picked up a micro rc LED light kit from rclighthouse.com. Very bright, with low power draw, fit very well.
Last edited by PRND21; Jan 06, 2013 at 04:16 PM.
Jan 06, 2013, 03:34 PM
Registered User
The result is a scale looking model that's very unique! The LiPo gives it gobs of power, I can't even open it up all the way inside! Even goes well over carpet with the taller scale tires. As you can imagine, it drifts and spins very well, especially on linoleum. The new, 2.4 technology really makes it shine, not having all the glitching (or ridiculas looking long antenna coming through the roof) to contend with as the AM radio did. A special thanks to atomicmods.com and rclighthouse.com, for it just wouldn't be the same without their rims or lights. I'll have to try and get some video of it eventually, just brainstorming where I want to shoot it before going ahead with that. Thoughts? Thanks for looking...
Last edited by PRND21; Jan 07, 2013 at 09:01 PM.
Jan 06, 2013, 10:11 PM
obey gravity, it's the law
Sweet. Nice work
Jan 07, 2013, 10:10 AM
Registered User
wparsons's Avatar
Awesome build!
Jan 07, 2013, 07:45 PM
in memory of dez RIP
rcphreak's Avatar
wow this is a realy great build for sure a one of a kind and with an icon of a car you make us jelious for sure .
Jan 16, 2013, 05:26 PM
Registered User
Badassness! Great job!
Jul 14, 2013, 10:43 PM
Registered User
Just thought I'd give an update for anyone else looking to do info on custom bodies for their Mini Z. I finally bit the bullet, and broke down and bought an MR-03 chassis to replace the hacked and admittedly tired MR-01. What a difference in the way this car drives now- wish I did it sooner! Very responsive and controllable. This time I used carbon fiber for the extension, with the stock H-plate at the end. Absolutely no flex except for at the suspension point. I think in the future I may change the motor mount to a mid mount, and possibly add a gyro since it has so much umph with the modified motor and lipo. This weekend, I managed to get a picture of it with the real Christine used in the movie at the Carlisle Chrysler Nationals, where they were commemorating the 30th anniversary of the film. Now it's time to start on a 59 Cadillac ambulance with functional lights and siren...
Jul 22, 2013, 03:51 PM
Time For Me To Fly!
fastmax's Avatar
Very nice work. Looks fantastic!!
Aug 03, 2016, 09:02 PM
Registered User
And finally got around to a video...3 years later
Kyosho Mini Z - 1958 Plymouth Christine Movie Car Custom Body in 1/25 Scale (2 min 24 sec)
Aug 07, 2016, 02:16 PM
Time For Me To Fly!
fastmax's Avatar
Man I really love that thing. Again, very nice job with the replica.

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Sex-crime Victim Could be Jailed for Tweeting her Attackers' Names Highflight Life, The Universe, and Politics 3 Jul 22, 2012 08:47 PM
Discussion Got her on her feet today jeffmete Electric Ducted Fan Jet Talk 16 Feb 13, 2012 02:03 AM