Thread Tools
Feb 08, 2013, 07:12 AM
Suspended Account
Quote:
Originally Posted by syndr0me View Post
Was there a difference? I didn't see any after the upgrade. The charger continued to work flawlessly for our needs. I was able to bypass the balance board and plug directly into the charger (2S car packs don't have a traditional balance plug) which made wiring a lot less convoluted. Worked perfectly.
Most obvious to me is the number of lipo cells in the upper part of each display.
Sign up now
to remove ads between posts
Feb 08, 2013, 07:16 AM
Registered User
EP Buddy.com
Feb 08, 2013, 07:19 AM
Suspended Account
Somewhat steep learning curve on this one Brazilian dude, but the display is gorgeous!
Feb 08, 2013, 04:03 PM
Registered User
Quote:
Originally Posted by JohnathanSwift View Post
Somewhat steep learning curve on this one Brazilian dude, but the display is gorgeous!

talking about me?
Feb 08, 2013, 04:27 PM
Suspended Account
Quote:
Originally Posted by Jonnydb View Post
talking about me?
Yup. If.you buy one, be ready....
Feb 09, 2013, 01:46 AM
Registered User

Parralel charging questions


Ok so I've just got my charger and ep buddy paraboard v3, I've hooked up 4 2s lipos with the leads and balance leads connected, should I be reading 8 cells on the voltage screen or still only 2, I'm only seeing 2 but thought I may have it wrong as I thought 8 would show up?

Cheers Justin
Feb 09, 2013, 02:13 AM
wjs
wjs
William
Quote:
Originally Posted by Jpm76 View Post
Ok so I've just got my charger and ep buddy paraboard v3, I've hooked up 4 2s lipos with the leads and balance leads connected, should I be reading 8 cells on the voltage screen or still only 2, I'm only seeing 2 but thought I may have it wrong as I thought 8 would show up?

Cheers Justin
Only 2 as same cells from each pack are connected in parellel on the paraboard.
Feb 09, 2013, 02:29 AM
Registered User
Quote:
Originally Posted by JohnathanSwift View Post
Somewhat steep learning curve on this one Brazilian dude, but the display is gorgeous!
I found it pretty intuitiv, a lot easier to get going than my PL8. There are advanced featuresvto play with, but to just start charging you dont even need to open the manuall
Feb 09, 2013, 03:25 AM
Registered User
Quote:
Originally Posted by wjs View Post
Only 2 as same cells from each pack are connected in parellel on the paraboard.
Thanks for that I wasn't sure but now I think about it since there in parallel it's stands to reason.

Also when charging say 4 packs, 5000mah at 2c (40amps), if one pack was slighly more discharged, towards the end of the cycle would it receive 40 amps or because there all in parallel would the higher volts of the other 3 packs act as a charger and bring the lower voltage pack up to the same level as the higher 3?

Another question, I can't work out what charge end current is, it's set as default 10% but not sure what it does?
Cheers
Feb 09, 2013, 05:58 AM
Registered User
Cavokk's Avatar
Quote:
Originally Posted by Jpm76 View Post
Thanks for that I wasn't sure but now I think about it since there in parallel it's stands to reason.

Also when charging say 4 packs, 5000mah at 2c (40amps), if one pack was slighly more discharged, towards the end of the cycle would it receive 40 amps or because there all in parallel would the higher volts of the other 3 packs act as a charger and bring the lower voltage pack up to the same level as the higher 3?

Another question, I can't work out what charge end current is, it's set as default 10% but not sure what it does?
Cheers
Hi

There is NO difference in voltage of the cells and packs because they are parallel. The current when you are charging is shared among the cells / packs in the way that the pack/cell with lowest internal resistance draws more current than the one with high internal resistance.

When you couple packs or cells in parallel you equalize the voltage over them, - so for at short period if pack voltage differs when you connect them in parallel then the pack with highest voltage charges the other pack(s) very quickly.

Cheers

C
Last edited by Cavokk; Feb 09, 2013 at 07:10 AM. Reason: Language
Feb 09, 2013, 06:21 AM
Registered User
Quote:
Originally Posted by JohnathanSwift View Post
Yup. If.you buy one, be ready....
yes i know! i was watching this charger since april of last year when was announced. mainly of features like 40A /70A of discharger.

and now is time to buy one
Feb 09, 2013, 06:24 AM
Registered User
Quote:
Originally Posted by Felborn View Post
I found it pretty intuitiv, a lot easier to get going than my PL8. There are advanced featuresvto play with, but to just start charging you dont even need to open the manuall

Yup, looking the display looks easy compared of mine Turbo 35 GFX
Feb 09, 2013, 06:26 AM
Registered User
Quote:
Originally Posted by The Tug View Post
EP Buddy.com

thanks Dude!




and about hobbyhut? is recommended?
Feb 09, 2013, 07:00 AM
Suspended Account
WOW! this charger is REALY EXPENCIVE! Although I have the funds to buy this if I wanted to, I dont think I would spend this much on a charger of any kind.
Feb 09, 2013, 07:35 AM
F3P, Slap, IMAC, Helis
Its cheaper then buying 2pl8 so In retrospect its not that bad considering your get 2pl8s in it one


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Article iCharger 4010Duo - Review CSpaced Batteries and Chargers 264 Mar 14, 2017 10:00 AM
Question What else has Jack been hiding from us? Newtron North Coast Electric Flyers 2 Mar 05, 2012 10:09 PM
Suggestion How do I know if my warning point has been retracted AndyOne Site Suggestions / Complaints 2 Mar 05, 2012 08:21 AM
Sold message has been deleted sonicboom24 Cars - Cars and Parts (FS/W) 0 Feb 22, 2012 12:34 PM