Thread Tools
Old Jan 19, 2013, 12:30 PM
bladeguy5 is offline
Find More Posts by bladeguy5
Registered User
bladeguy5's Avatar
I wonder how this compares to the yak 54
Sign up now
to remove ads between posts
Old Jan 19, 2013, 01:26 PM
Tomdomification is offline
Find More Posts by Tomdomification
Registered User
Tomdomification's Avatar
I so dumb...

Tom :-)
Last edited by Tomdomification; Jan 19, 2013 at 06:46 PM.
Old Jan 19, 2013, 01:58 PM
bobly is offline
Find More Posts by bobly
Registered User
Quote:
Originally Posted by Tomdomification View Post
Carbon-z? Well to start of with, this plane is designed for 3D whereas the Yak is more of a sports model, capable of some 3D.
Tom :-)
???
Old Jan 19, 2013, 06:13 PM
accel8or is offline
Find More Posts by accel8or
Mark Beltran
accel8or's Avatar
Problem with the elevator. Not getting full throws. Is this normal until as3x kicks in?

Got everything per the instructions (on the elevator): servo travel 125%. dual rate high: 100% expo: 20%

Re-binded and still very little elevator servo travel. Does not appear to be struggling or pinched against something. The elevator connecting rod was placed in-factory at the furthest part of the servo horn, and at the innermost hole at the elevator horn.
Old Jan 19, 2013, 07:01 PM
echoplanar is offline
Find More Posts by echoplanar
Registered User
echoplanar's Avatar
Well that was a fast 20 min to get the plane ready to bind.

The box was bigger than I expected and the plane is too-hope to get some flights tomorrow.

Jon
Old Jan 19, 2013, 07:16 PM
Beach Copter is offline
Find More Posts by Beach Copter
Registered User
accel8or

Try changing thr gear switch to #1 position from #0.

This on mine changed both thr throw of elevator as well as 3D settings
Old Jan 19, 2013, 07:20 PM
turboparker is online now
Find More Posts by turboparker
I'd rather be flying!
turboparker's Avatar
Quote:
Originally Posted by accel8or View Post
Problem with the elevator. Not getting full throws. Is this normal until as3x kicks in?

Got everything per the instructions (on the elevator): servo travel 125%. dual rate high: 100% expo: 20%

Re-binded and still very little elevator servo travel. Does not appear to be struggling or pinched against something. The elevator connecting rod was placed in-factory at the furthest part of the servo horn, and at the innermost hole at the elevator horn.
Is the rx in 3D mode or general flight mode? According to the manual, you need to be in 3D flight mode to get full throws.

Joel
Old Jan 19, 2013, 08:35 PM
ChuckTseeker is offline
Find More Posts by ChuckTseeker
Registered User
ChuckTseeker's Avatar
Oh boy oh boy oh boy! just had the maiden with the Parkzone VisionAire

no trimming needed, flew off the ground straight and true like it was on rails, straight up and into a hover does so much and this was in General and D/R at 70%
I then flicked it onto 100% rates in General and to start with i think most will be blown away at how it responds.
I then flicked back to low rates and hit the 3D switch man so much fun, this plane flys so slow, but just stays under control anyway having 3 position switches i set a mid position on the 3D and flicked to that, it was mind blowing for a noob like me, i never put them on 100% being my first flight, but will try them as soon as i get more comfortable, as this is not my plane and has to go back for other engagements oh landing was easy i had to go round again because i miss judged the first and wanted to land in front which was a cinch to do as your see in the video

anyway i'm off to cool down it was bloody hot out there then it's time to edit the vid and get it uploading

cheers chuck

PS oh did i mention your gonna love this plane
Old Jan 19, 2013, 08:40 PM
turnerm is offline
Find More Posts by turnerm
Gone Huckin'
turnerm's Avatar
Quote:
Originally Posted by ChuckTseeker View Post
Oh boy oh boy oh boy! just had the maiden with the Parkzone VisionAire

no trimming needed, flew off the ground straight and true like it was on rails, straight up and into a hover does so much and this was in General and D/R at 70%
I then flicked it onto 100% rates in General and to start with i think most will be blown away at how it responds.
I then flicked back to low rates and hit the 3D switch man so much fun, this plane flys so slow, but just stays under control anyway having 3 position switches i set a mid position on the 3D and flicked to that, it was mind blowing for a noob like me, i never put them on 100% being my first flight, but will try them as soon as i get more comfortable, as this is not my plane and has to go back for other engagements oh landing was easy i had to go round again because i miss judged the first and wanted to land in front which was a cinch to do as your see in the video

anyway i'm off to cool down it was bloody hot out there then it's time to edit the vid and get it uploading

cheers chuck

PS oh did i mention your gonna love this plane
Cool! Can't wait to see the video!
Old Jan 19, 2013, 09:26 PM
JimmyJet727 is offline
Find More Posts by JimmyJet727
Road Scholar
JimmyJet727's Avatar
Hey folks, battery question. I have several 2200mah 20C batteries. Parkzone recommends 25C for the Visionaire. I'm a total 3D newbie and *not* looking for ultimate performance. Will the 20C batteries be okay?

Thanks, JJ
Old Jan 19, 2013, 09:42 PM
3drcparts is offline
Find More Posts by 3drcparts
inverted-i-fly
3drcparts's Avatar
Quote:
Originally Posted by JimmyJet727 View Post
Hey folks, battery question. I have several 2200mah 20C batteries. Parkzone recommends 25C for the Visionaire. I'm a total 3D newbie and *not* looking for ultimate performance. Will the 20C batteries be okay?

Thanks, JJ
should be fine for low and slow
Old Jan 19, 2013, 09:54 PM
turnerm is offline
Find More Posts by turnerm
Gone Huckin'
turnerm's Avatar
Quote:
Originally Posted by JimmyJet727 View Post
Hey folks, battery question. I have several 2200mah 20C batteries. Parkzone recommends 25C for the Visionaire. I'm a total 3D newbie and *not* looking for ultimate performance. Will the 20C batteries be okay?

Thanks, JJ
Oh yea. You'll be ok. You'll notice the most of verticals but for everything else you should be just fine.

Did you pick one up from Mike?? Need someone to "test it out" for you??
Old Jan 19, 2013, 10:26 PM
accel8or is offline
Find More Posts by accel8or
Mark Beltran
accel8or's Avatar
Quote:
Originally Posted by turboparker View Post
Is the rx in 3D mode or general flight mode? According to the manual, you need to be in 3D flight mode to get full throws.

Joel
I'm gonna go thru the manual again to see where to do that. Know where it is offhand? Thanks Joel.
Old Jan 19, 2013, 10:30 PM
ChuckTseeker is offline
Find More Posts by ChuckTseeker
Registered User
ChuckTseeker's Avatar
Quote:
Originally Posted by accel8or View Post
I'm gonna go thru the manual again to see where to do that. Know where it is offhand? Thanks Joel.
Gear switch Position 0 is General Mode position 1 is 3D mode

cheers chuck

PS did i mention this plane is a blast
Old Jan 19, 2013, 10:35 PM
dalecheek1 is online now
Find More Posts by dalecheek1
Registered User
CHUCK hurry up with YOUR VIDEO,,,,,there are thousands of US waiting for your MAIDEN 3d ADVENTURE


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Parkzone's New Habu 2 EDF ChuckTseeker Foamy EDFs 5037 Oct 31, 2016 09:05 PM
For Sale New Parkzone S.E.5a w/ AR600 Rx - LPU Kevinfred Aircraft - Electric - Airplanes (FS/W) 1 Jul 12, 2012 01:26 AM
Sold New Parkzone S.E.5a w/ AR600 Rx - LPU Kevinfred Aircraft - Electric - Micro & Indoor Airplanes (FS/W) 1 Jun 23, 2012 10:10 AM