Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Jan 27, 2013, 12:31 PM
Ineedmoreparts is offline
Find More Posts by Ineedmoreparts
Registered User
I'll move gains back to 50. Put mix on Normal. (Not rubber navigation). Ailerons was assigned to channel 1. And re-test. It wags side ways. I never checked the rudder for stabilization. Only check with radio control. It could be reversed. And now that you mentioned that, I did had to reverse the elevator when checking for stabilization.

Thanks for the suggestions.
Sign up now
to remove ads between posts
Old Jan 27, 2013, 01:46 PM
Ineedmoreparts is offline
Find More Posts by Ineedmoreparts
Registered User
The rudder was counter acting in wrong direction. I've corrected and changed the mix to normal for testing. All gains at 50.

Can you point me to wear it says rudder nav should be assigned to channel 1?

I believe the plane was wagging telling me "dummy you"ve made a mistake"
Cant wait to test again

Thanks again!.
Old Jan 27, 2013, 02:31 PM
lemonsorbie is offline
Find More Posts by lemonsorbie
Registered User
Does the DoS v2.00 still work on planes or is it specific to multi-rotors

Tx
Old Jan 28, 2013, 08:49 AM
wippo76 is offline
Find More Posts by wippo76
Registered User
[QUOTE=Ineedmoreparts;23947726]The rudder was counter acting in wrong direction. I've corrected and changed the mix to normal for testing. All gains at 50.

Can you point me to wear it says rudder nav should be assigned to channel 1?

I believe the plane was wagging telling me "dummy you"ve made a mistake"
Cant wait to


So you connect rudder to ch 1 if there are no ailerons
But you have I understand right?
You can try rud nav but I had better luck with aileron nav
I think your problem was rudder is reversed

Good re maiden
Old Jan 28, 2013, 08:50 AM
wippo76 is offline
Find More Posts by wippo76
Registered User
Quote:
Originally Posted by lemonsorbie View Post
Does the DoS v2.00 still work on planes or is it specific to multi-rotors

Tx
2.0 is not for planes so dont try it
Old Jan 28, 2013, 12:50 PM
Ineedmoreparts is offline
Find More Posts by Ineedmoreparts
Registered User
I'm going to go out a limb and state that I thought RUD nav was more for 3D operation in 3D mode. With other stablization systems there is no need to change channel assignments. So if I have ailerons and rudder, does the channel assignment stay the same(ail Channel 1, Rudder channel 4? If a wanted to do a knike edge in 3d mode, wouldnt I chose Normal setup with Rudder Nav? That just a question, I cant do knife edges?!?!?!?!?!?!!!??

In other words can you do 3D flight if you chose 1. Normal vs 4. Normal(rud NAV)?

After serveral attempts my emails to feiyu have finally gotten thru their spam filter.
Old Jan 28, 2013, 01:38 PM
lbarreiro is offline
Find More Posts by lbarreiro
FPV 23Km
lbarreiro's Avatar
I just sent a email to FeiYu Tech regarding the minimum altitude in the RTH mode

"Hi,
I'm using your´s new autopilot DOS in a new Zephyr2. I'm very happy with it. It's easy and practical. I own the older brothers, 21AP and the 31AP, but DOS it's a step ahead.

However I wante to ask to include a minimum altitude in the RTH mode, because besides being safer is a point in favor of other existing autopilot.
In my experience with 21AP and 31AP beyond knowing that the airplane always climbed to the minimum altitude, i also used this feature to launch the plane.

Best Regards"
Old Jan 28, 2013, 07:29 PM
Ineedmoreparts is offline
Find More Posts by Ineedmoreparts
Registered User
Success!!!!! I did a short test this evening in windy conditions. My plane returned to home and circled over head. Made me nervous when going with the wind, but handled it great.

Thanks for the help.
Old Jan 29, 2013, 02:12 AM
wippo76 is offline
Find More Posts by wippo76
Registered User
Off course succes
Fy dos works great
Happy we could help you out
Old Jan 29, 2013, 11:26 AM
mrracer98 is offline
Find More Posts by mrracer98
Registered User
https://www.rcgroups.com/forums/show....php?t=1819632

fy-31ap 160 NIB. Thanks!
Old Jan 29, 2013, 09:32 PM
saabguyspg is offline
Find More Posts by saabguyspg
saabguyspg's Avatar
good buy, you will love it.

Steve
Site Sponsor
Old Jan 29, 2013, 10:04 PM
mrracer98 is offline
Find More Posts by mrracer98
Registered User
Quote:
Originally Posted by saabguyspg View Post
good buy, you will love it.

Steve
I'm trying to sell it! I have too much stuff!!!
Old Jan 29, 2013, 10:13 PM
saabguyspg is offline
Find More Posts by saabguyspg
saabguyspg's Avatar
hahah.. funny, my bad
Site Sponsor
Old Jan 30, 2013, 06:08 AM
lbarreiro is offline
Find More Posts by lbarreiro
FPV 23Km
lbarreiro's Avatar
Reply from Feiyu Team.

"Dear Sir

Thank you for your support!
From your mail say:However I wanted to ask to include a minimum altitude in the RTH mode.
Sorry,the DoS not include a minimum altitude in the RTH mode.
The return to home altitude is the switch point altitude.

Best regards!
Feiyu Team"
Old Jan 30, 2013, 09:02 AM
wippo76 is offline
Find More Posts by wippo76
Registered User
Hehe yes thats what we know too
Tipical chinese answer
Just say no I dont know
Maybe in future

Hope it will come
As for now dont fly to low far away


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold FY - 31AP Autopilot Path Navigation & Hornet OSD Combo GPS For RC Airplane mamut FPV Equipment (FS/W) 1 Sep 08, 2012 06:34 AM
Sold FY-31 autopilot with Hornet OSD willi_m FPV Equipment (FS/W) 2 Jun 26, 2012 01:31 AM
Sold FY-21AP II Autopilot with AP117 OSD (latest version!) Mr.RC-CAM FPV Equipment (FS/W) 0 Oct 30, 2010 12:14 AM