Fox .36 MK5 P/L - RC Groups
Thread Tools
This thread is privately moderated by noarf4me2, who may elect to delete unwanted replies.
Dec 13, 2012, 01:18 AM
Trader Rating: 41
Get airborne !
noarf4me2's Avatar
Wanted

Fox .36 MK5 P/L


It finally happened, circlip came out and ruined the bore !
looking for some parts , circlip for wristpin, P/L.... this is a Fox .36 with no markings on the case...but I think it's a version of a mark 4 combat special.....thanks in advance.
Sign up now
to remove ads between posts
Dec 13, 2012, 07:01 AM
Trader Rating: 113
Tucker and Daisy
VampeD4's Avatar
try this. Fox is still around http://www.foxmanufacturing.com/inde...ndex&cPath=143
Dec 13, 2012, 08:55 AM
Trader Rating: 133
Registered User
Cougar429's Avatar
I believe this is a Fox 36 C/L motor I just cleaned up a couple of weeks ago. Is this the one you're looking for?
Dec 13, 2012, 12:33 PM
Trader Rating: 29
Registered User
McCoy .35/ Fox .35 stunt. McCoy should have no on it .29/.35/.40 same case and use to have a red head,. Fox he is looking for is like Combat special MK3/MK4/MK6/mk7etc.
Dec 13, 2012, 05:40 PM
Trader Rating: 41
Get airborne !
noarf4me2's Avatar
Dankar04 is right, couldnt get any pics posted but the engine has the square venturi, probably 1980 + vintage......
Dec 13, 2012, 08:32 PM
Trader Rating: 2
Bigiron
I think I have a MK V P&C set and the wrist pin and circlips in my junk barrel. I will need more informstion. Contact me at mdenny4@cox.net.

Bigiron
Dec 13, 2012, 09:57 PM
Trader Rating: 133
Registered User
Cougar429's Avatar
The red on the McCoy didn't survive the hot glycol bath.
Dec 14, 2012, 04:23 PM
Trader Rating: 2
Bigiron

Fox Parts


noarf4me, does your engine that you need parts for have a flat topped piston or a baffle on the top?

Bigiron
Dec 14, 2012, 05:17 PM
Trader Rating: 41
Get airborne !
noarf4me2's Avatar
BigIron,
It's the flattop type with small radiuss on the lower part of skirt, the wristpin is .155 dia.
Hope that helps ID it, let me know what the cost and how you want paid...Thanks
Flyin CL speedlimit combat here in Concord CA. at one of the oldest CL fields in CA.
Dec 14, 2012, 07:53 PM
Trader Rating: 2
Bigiron

Fox parts.


Does the engine have one ball bearing at the rear of the crank shaft but none at the front? If so, that is a MK V If it has a large four lug drive (thrust) washer and Double ball bearings, it is a MK IV I have some parts for all the MK series except the VII I also have several complete engines. I used to fly both fast and slow combat very competitively so I got LOTS of support stuff.

To be sure, I would like for you to give me a call on the Ma Bell some time. I am home most of the time on weekends but sometimes I am hard to catch on week days unless after 5 PM central. I am in the central time zone.

My E-Mail Address is mdenny4@cox.net and the phone # is (316)838-8494

Ask for Bigiron or Marvin
Dec 14, 2012, 08:30 PM
Trader Rating: 41
Get airborne !
noarf4me2's Avatar
Marvin,
I'll give you a call tomorrow
Dec 17, 2012, 01:16 PM
Trader Rating: 2
Bigiron

Fox Parts


Noarf, My server went down and I failed to receive any e mail sent to me the past 5 days. If you sent me anything, re-send it.

Bigiron


Quick Reply
Message:
Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Fox 36 X jsesere Engines 29 Sep 04, 2013 01:52 PM
Sold Fox .35 Stunt C/L Engine. richardc951 Aircraft - Fuel - Engines and Accessories (FS/W) 0 Jul 03, 2012 01:14 PM
Sold Fox .15 C/L Engine #1150 richardc951 Aircraft - Fuel - Engines and Accessories (FS/W) 0 Jul 03, 2012 01:12 PM
Sold L@@K! Sundowner 36 Receiver Ready with Evo 40NX Rifraf Aircraft - Fuel - Airplanes (FS/W) 0 Mar 31, 2012 08:50 PM
For Sale C/L fox 36, metal/plastic fuel tanks + more jim e Aircraft - Fuel - Engines and Accessories (FS/W) 7 Jul 13, 2007 08:23 AM