10cc (.60 cu. in.) Gas Engine by Evolution Engines - Page 26 - RC Groups
Thread Tools
Jan 21, 2013, 08:16 PM
Engine Category Manager - EVO,
Quote:
Originally Posted by DMHIGHFLYER
Do I need to use a spacer with the Bisson pitts on the Evo10cc? Thanks
That will depend upon the airplane and engine mounts you are planning to use. In our testing with 'typical' engine mounts has shown that a spacer is not needed to clear the engine mount.

Pete
Sign up now
to remove ads between posts
Jan 21, 2013, 09:09 PM
Registered User
rjstrickjr's Avatar
Quote:
Originally Posted by Pete Bergstrom
That will depend upon the airplane and engine mounts you are planning to use. In our testing with 'typical' engine mounts has shown that a spacer is not needed to clear the engine mount.

Pete
I did not need a spacer on mine. I will however, when I figure out how to remove the broken screw, use a couple of washers due to the leanth of the screw.
Jan 23, 2013, 06:55 PM
Sucker for biplanes
DMHIGHFLYER's Avatar

10cc


Thanks, I got one order. The BIS04046 is hard to find, everyone is out of stock. I see that Slimline makes a pitts for an OS .46, It may fit the Evo 10cc.
Latest blog entry: Hobbyzone sport cub
Jan 23, 2013, 07:28 PM
Gas Only
Fokker DII's Avatar
Pete, or someone at Horizon, can you tell me Why the manual specificaly prohibits using Amsoil Pro in the Evo .10?
That IS what I use in my Saito FG14 at 20:1, and I wonder why it is not bad for that one too? Or is it?
I hate to have so many gas cans & pumps, (now 4), for each specific engine I own that all have different reccomendations!. (Kind'a a nuisence)
Jan 24, 2013, 06:58 PM
Sucker for biplanes
DMHIGHFLYER's Avatar

10cc


I would like to run Klotz modelube in my engine. I'm running it at 32:1 and 40:1, for other engines. I have bought Evolutions mix oil for break in 20:1, but in the future would like to switch and run the same oil for all my engines.
Latest blog entry: Hobbyzone sport cub
Jan 24, 2013, 08:50 PM
Engine Category Manager - EVO,
Fokker DVII

We have some experience through our service department with Amsoil lubed engines that leads us to proceed with caution. In general the problem has not been quality of the oil but user confusion on how best to use the oil. As this engine is intended for users new to any engine as well as experienced modelers such as you, we designed the operating specs to provide the most reliable and user friendly experience possible.

Pete
Jan 24, 2013, 08:51 PM
Engine Category Manager - EVO,
Quote:
Originally Posted by DMHIGHFLYER
I would like to run Klotz modelube in my engine. I'm running it at 32:1 and 40:1, for other engines. I have bought Evolutions mix oil for break in 20:1, but in the future would like to switch and run the same oil for all my engines.
Klotz oil has been tested and works ok. Please be sure to run it at 20:1 until we have more data on lower oil levels.

Pete
Jan 24, 2013, 09:31 PM
Gas Only
Fokker DII's Avatar
Thanks for clarifying the information Pete. I am breaking the engine in with Castrol 2 stroke oil @ 20:1 and after a gallon or so I will change to a synthetic but continue at 20:1 as I do with my Saito FG-14.
Love this little engine
Jan 24, 2013, 09:43 PM
Registered User
AA5BY's Avatar
I've now one hundred minutes flight time and also enjoying the engine greatly.
Jan 24, 2013, 11:13 PM
Sucker for biplanes
DMHIGHFLYER's Avatar

10cc


Thanks Pete, looks like I'm going to order a second 10cc for my H9 Corsair 50.
Latest blog entry: Hobbyzone sport cub
Jan 24, 2013, 11:15 PM
Sucker for biplanes
DMHIGHFLYER's Avatar
Quote:
Originally Posted by AA5BY
I've now one hundred minutes flight time and also enjoying the engine greatly.
Wish I lived in Texas, I would be able to fly every day
Latest blog entry: Hobbyzone sport cub
Jan 24, 2013, 11:23 PM
Registered User
AA5BY's Avatar
Quote:
Originally Posted by DMHIGHFLYER
Wish I lived in Texas, I would be able to fly every day
We do enjoy flying year round with some nice days during winter. We suffer a bit of heat from June through September however.
Jan 24, 2013, 11:25 PM
Registered User
And we pass out the flyers on how to detect heat stroke.
Edwin
Jan 24, 2013, 11:48 PM
Registered User
AA5BY's Avatar
In summer, I rarely arrive at the field before 3pm and then usually sit under the pavilion until five before getting serious about flying.
Jan 25, 2013, 01:25 AM
Expo is built into my thumbs
Hance's Avatar
Well my 10GX is mounted up and ready to go. Yes the covering is wrinkled BAD but we have like 10% humidity right now. Not even going to mess with it until it warms up. The covering was tight as a drum and didn't have a single wrinkle when the plane came out of the box.



DSCN0138 by Hance1976, on Flickr


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Hangar 9 Meridian Sport ARF and Evolution 10cc Gas Engine Bajora Sport Planes 441 Apr 13, 2017 05:03 PM
Sold Fox 4.2 cu. in. (70cc) gas engine, electronic ignition, runs great barchiola Aircraft - Fuel - Engines and Accessories (FS/W) 7 Nov 19, 2012 08:07 PM
For Sale Evolution 58cc gas engine with new KS header parts and new Evolution tuned canister Daveyboycfs Aircraft - Fuel - Engines and Accessories (FS/W) 0 Jun 11, 2012 11:07 PM
Sold US Engines NIB 41cc (2.5 cu in) gas engine. REDUCED !! puplover Aircraft - Fuel - Engines and Accessories (FS/W) 0 Oct 15, 2011 02:41 PM
Sold Saito FG-36 4 stroke gas engine (2.2 cu in) James Love Aircraft - Fuel - Engines and Accessories (FS/W) 0 Mar 23, 2011 12:16 AM