Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Dec 14, 2012, 09:36 AM
blueprint is offline
Find More Posts by blueprint
FPV Pilot
blueprint's Avatar
Nice daemon. Do u have pictures of ur setup?
Sign up now
to remove ads between posts
Old Dec 14, 2012, 10:08 AM
rclab1 is offline
Find More Posts by rclab1
USA: LakeGeorge, New York
typicalaimster
Another thing you can do is drill three holes in the fuse and glue three bottle caps in place. Like the holes on a bowling ball. The zaggy folks uses to do this. It gives you a place to grip and push off from. Just don't tell TIC you're doing it!


+1
Old Dec 14, 2012, 11:18 AM
boopidoo is offline
Find More Posts by boopidoo
On a holiday?
boopidoo's Avatar
The ad is funny but in a teenager kind of way, "Skyhunter the best fpv plane ever" LOL. Why not write something substantial or even remotely true?
Old Dec 14, 2012, 01:18 PM
jayb1rdz is offline
Find More Posts by jayb1rdz
Never fly an A model anything!
jayb1rdz's Avatar
https://www.rcgroups.com/forums/atta...mentid=4042053

This is what I did to the SW. It worked well but was more a tinkering effort than anything.

I flew behind a large farm shed and lost both VTX and RX link destroying it.

I enjoy the flying more keeping the model light and simple now and that how I'll probably keep my SH unless it's just too difficult to launch.....which I doubt.
Old Dec 14, 2012, 02:00 PM
rclab1 is offline
Find More Posts by rclab1
USA: LakeGeorge, New York
as I look back, my old SkyWalker v5 was like a "RUBBER" plane.
This SkyHunter has no flexing I see no flexing on mine whatsoever....!
(its stout!).
Last edited by rclab1; Dec 14, 2012 at 07:37 PM.
Old Dec 14, 2012, 02:34 PM
Daemon is online now
Find More Posts by Daemon
Registered User
Daemon's Avatar
If you can get your hand around the fat fuse, it's not difficult to hand launch (at least with one
battery so far). If you look at the third launch in my first SH vid, can see that the trick is to hold it
behind you tipped nose high so it doesn't try to pull itself forward out of your hand before you
can throw it, then give it a good upwards loft as it arcs over your head. The 12" prop is even
with the bottom of the fuse, and my hand is well away from the fuse an instant after release,
and the plane doesn't drop at all. Had a little headwind for that launch, but I don't expect to
see problems in no wind.

ian
Old Dec 14, 2012, 07:25 PM
skyhunter_1 is offline
Find More Posts by skyhunter_1
FPV Engineer
skyhunter_1's Avatar
Quote:
Originally Posted by Blueshy View Post
I don't think that number is amps. I think the number under the voltage was
amps. Looks like 15ish to me. I don't think it would be aerodynamically possible
to do 2-3A at 65kph with that large a plane, or if it is it would have to be
extremely aerodynamic. 20-40 watts just isn't enough.

-Blues
Skyhunter normal cruise amps is about 8A (4S 15000mah nano battery, no wind),the FPV video in home page is OSD Autopilot go home, following wind and drop height, so amps is 2-3A
Old Dec 14, 2012, 07:52 PM
Blueshy is offline
Find More Posts by Blueshy
OSUFPV - KF7VFT
Quote:
Originally Posted by skyhunter_1 View Post
Skyhunter normal cruise amps is about 8A (4S 15000mah nano battery, no wind),the FPV video in home page is OSD Autopilot go home, following wind and drop height, so amps is 2-3A
Yes, but as Daemon already pointed out, the plane was rapidly descending in
altitude during that time. My point was about cruising amps being as low
as 2-3A. Besides, Daemon already averaged ~7A on a 3 cell. Your 8A cruising
number is a bit high for a 4 cell.

-Blues
Old Dec 14, 2012, 10:06 PM
wannabe is offline
Find More Posts by wannabe
Been modding for over 35 years
wannabe's Avatar
Ian, did you have a chance to weigh everything?
Old Dec 14, 2012, 11:54 PM
Daemon is online now
Find More Posts by Daemon
Registered User
Daemon's Avatar
Posted it earlier in the thread. 2.2Kg with a 3S 4000mAh pack. 2.3Kg with a 5000mAh pack.
Old Dec 15, 2012, 12:59 AM
CambriaHobby is online now
Find More Posts by CambriaHobby
Registered User
Has any one used the glue that came with the SkyHunter?

I wondering if I should use it or CA..
Old Dec 15, 2012, 01:00 AM
Daemon is online now
Find More Posts by Daemon
Registered User
Daemon's Avatar
Stock glue is probably safer to supply for those who are not familiar with how to work with CA.
Old Dec 15, 2012, 01:03 AM
CambriaHobby is online now
Find More Posts by CambriaHobby
Registered User
OK
Thanks
Old Dec 15, 2012, 01:03 AM
bignose13 is offline
Find More Posts by bignose13
Yeah Baby
bignose13's Avatar
Quote:
Originally Posted by Daemon View Post
Stock glue is probably safer to supply for those who are not familiar with how to work with CA.
Without doubt the best to use in my opinion, also if you run short, get UHU POR, even better, thinking about it get the UHU before the stock glue
However, it's only good if you use it properly, DONT glue then join straight away, wait till the glue has dried before joining together
Old Dec 15, 2012, 02:28 AM
OzparkPilot is offline
Find More Posts by OzparkPilot
Watts up ?
OzparkPilot's Avatar
Daemon, can we see a few pix of the SH and equipment placement please ?>


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product New FPV PLANE: Bormatec FPV rclab1 FPV Aircraft 109 Jul 12, 2016 03:36 AM
Discussion Discrimination against individuals professing strong belief in the supernatural? H2SO4 Life, The Universe, and Politics 66 Jan 04, 2016 11:20 PM
Cool Skyhunter - New 1.8m twintail FPV/UAV EPO platform vigor FPV Talk 58 Nov 26, 2012 06:54 PM
Sold Complete FPV Plane, Ground Station, Autopilot, Dual Camera 27x zoom + more NEW crd Aircraft - Electric - Airplanes (FS/W) 3 Mar 09, 2012 10:22 PM
Sold Complete FPV Plane, Ground Station, Autopilot, Dual Camera 27x zoom + more NEW crd FPV Equipment (FS/W) 5 Mar 06, 2012 08:01 PM