Thread Tools
Old Jan 04, 2013, 11:26 AM
d_wheel is offline
Find More Posts by d_wheel
Old fart. VAAATSP
d_wheel's Avatar
Quote:
Originally Posted by vespa View Post
That optical stuff is expensive and a pain to mount, especially in airplanes but even worse in cars and boats.
You got that right. I finally got it mounted on my helicopter, but it wasn't easy! The eagletree sensor would be much, much easier to install. However, a friend flies with spektrum and it uses this type sensor. On his bird it is very erratic. Shows fine for a while then goes to 6000 rpm. Probably just an isolated case. Anyone else seen this problem?

Later;

D.W.
Sign up now
to remove ads between posts
Old Jan 05, 2013, 08:13 AM
RC Man is offline
Find More Posts by RC Man
A man with too many toys

Bit Resolution


I am having a hard time finding the resolution for the various Futaba technologies.

FHSS
S-FHSS
FASST
FASSTest

Also do FASST 7-channel, MULTI, and MULTI2 modes all have the same resolution? I think I read that FASST was 2048 but not 100% sure?


Old Jan 05, 2013, 09:02 AM
RC Man is offline
Find More Posts by RC Man
A man with too many toys
Quote:
Originally Posted by RC Man View Post
I am having a hard time finding the resolution for the various Futaba technologies.

FHSS
S-FHSS
FASST
FASSTest

Also do FASST 7-channel, MULTI, and MULTI2 modes all have the same resolution? I think I read that FASST was 2048 but not 100% sure?


My concern is that if I use a cheap FHSS 4-channel receiver will I be loosing any resolution?


.
Old Jan 05, 2013, 09:07 AM
dnbarrie11 is offline
Find More Posts by dnbarrie11
RV7guy
dnbarrie11's Avatar

Doubt it


Quote:
Originally Posted by RC Man View Post
My concern is that if I use a cheap FHSS 4-channel receiver will I be loosing any resolution?


.
Unless you are flying a precision 3D helicopter or possibly a well trimmed Pattern plane, I doubt you'd feel the difference.

Darwin N. Barrie
Chandler, AZ
Team Futaba
Old Jan 05, 2013, 09:38 AM
RC Man is offline
Find More Posts by RC Man
A man with too many toys
Quote:
Originally Posted by dnbarrie11 View Post
Unless you are flying a precision 3D helicopter or possibly a well trimmed Pattern plane, I doubt you'd feel the difference.

Darwin N. Barrie
Chandler, AZ
Team Futaba
I fly helicopters maximum resolution is critical for precision flying.

So I assume from the way you said it that its lower in FHSS but whats the number?

Old Jan 05, 2013, 09:50 AM
bdelapen is offline
Find More Posts by bdelapen
Sponsored by Team de la Pea
bdelapen's Avatar
Quote:
Originally Posted by RC Man View Post
My concern is that if I use a cheap FHSS 4-channel receiver will I be loosing any resolution?


.
Scary but I have not been able to find any documentation (whether web page or individual manuals) that state the resolutions of the receivers. If I had to guess - and this is not fact, just a guess - FASST 7CH mode and FHSS is 1024 the rest are at least 2048 though it definitely depends on the receiver.

Typically your limiting factor in resolution will not be the receiver but instead the servos, you need to have very high end servos for them to truly take advantage of the full resolution of the receiver. If you are going all out on the servos then it may be worth the little extra to upgrade from a FHSS to a FASST receiver.

- Birger
Old Jan 05, 2013, 12:46 PM
DougV is offline
Find More Posts by DougV
Registered User
DougV's Avatar
Quote:
Originally Posted by RC Man View Post
I am having a hard time finding the resolution for the various Futaba technologies.

FHSS
S-FHSS
FASST
FASSTest

Also do FASST 7-channel, MULTI, and MULTI2 modes all have the same resolution? I think I read that FASST was 2048 but not 100% sure?


FHSS = 1024
S-FHSS = No idea
FASST 7ch mode = 1024
FASST 8ch mode, MULT and MLT2 = 2048
FASSTest = 2048

Doug.
Old Jan 05, 2013, 02:28 PM
Vapor Trails is online now
Find More Posts by Vapor Trails
DFC~ We Do Flyin' Right
Vapor Trails's Avatar
Quote:
Originally Posted by bdelapen View Post
.

Typically your limiting factor in resolution will not be the receiver but instead the servos, you need to have very high end servos for them to truly take advantage of the full resolution of the receiver. If you are going all out on the servos then it may be worth the little extra to upgrade from a FHSS to a FASST receiver.

- Birger
Great answer, I could not have said it better myself.

Using regular servos like hs-65, I can tell no difference. But my new 64" mxs with its hs7245 servos and a 2048 resolution rx is noticeably faster, more precise and more responsive.
RCG Plus Member
Latest blog entry: Please kill isis
Old Jan 05, 2013, 06:01 PM
RC Man is offline
Find More Posts by RC Man
A man with too many toys
Quote:
Originally Posted by DougV View Post
FHSS = 1024
S-FHSS = No idea
FASST 7ch mode = 1024
FASST 8ch mode, MULT and MLT2 = 2048
FASSTest = 2048

Doug.
Thanks, that’s exactly what I wanted to know. I flew 1024 PCM for years and it was good. I wonder why they only made 1024 since it’s newer technology. I guess it’s the cost of keeping the price down.


I do use Futaba BLS servos on all my helicopters. They can take full advantage of 2048 and more. I agree if you still use analog servos who cares - LOL!


.
Old Jan 05, 2013, 11:40 PM
Mikarro is offline
Find More Posts by Mikarro
Suspended Account
Futaba 14SG 14-Channel 2.4GHz Computer Radio System (1 min 11 sec)
Old Jan 05, 2013, 11:57 PM
Fentonflyers is offline
Find More Posts by Fentonflyers
Registered User
Fentonflyers's Avatar
So I feel like it is close enough to the middle of January. How bout it?
RCG Plus Member
Old Jan 06, 2013, 09:28 AM
losifanatic is offline
Find More Posts by losifanatic
Sippin the Koolaid!
losifanatic's Avatar
I know right.
Old Jan 07, 2013, 10:29 AM
saab2 is offline
Find More Posts by saab2
Registered User
Hope to get them sooner, cause I also back order for 2 Unit
Old Jan 08, 2013, 01:51 AM
litrisbetr is offline
Find More Posts by litrisbetr
Registered User
Did you buy two so that you can save twice as many models,
without having to buy that pesky memory card that is not supplied?
Old Jan 08, 2013, 10:08 AM
spacewalker_ is offline
Find More Posts by spacewalker_
Registered User
spacewalker_'s Avatar


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Wanted Futaba 9cap\JRXP9303 Airplane\FUTABA 10C tx wanted Defacto Aircraft - General - Radio Equipment (FS/W) 8 Mar 26, 2013 07:54 PM
Whoops! The Futaba 8J S-FHSS is better than Futaba 18MZ S-FHSS! The 8J may get Telemetry... SimonChambers Radios 1 Jul 09, 2012 05:54 PM
Sold Genuine Futaba GY401 gyro with Futaba S9650 servo BD Flyer Aircraft - Electric - Helis (FS/W) 1 Jul 01, 2012 11:33 PM
Sold Genuine Futaba GY401 gyro with Futaba S9650 servo BD Flyer Aircraft - General - Radio Equipment (FS/W) 3 Jun 27, 2012 10:47 PM
Sold Futaba S9650 Digital Servo + Futaba Gryo GY401 / Futaba 2.4GHz 8Ch R608FS wefao Aircraft - General - Radio Equipment (FS/W) 4 Mar 10, 2012 09:45 PM