New Products Flash Sale
Thread Tools
Old Nov 12, 2012, 12:07 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
The firewall is 3/16 hard ply. Figured the nose sheeting had to be in place before more could be done with the uc struts.... then the firewall has to be in place before the nose sheeting....
Not yet certain where the battery will go. The bottom sheet has been tack glued in place for sanding, guessing it will be the hatch.
Last edited by phillip57; Nov 18, 2012 at 05:34 PM.
Sign up now
to remove ads between posts
Old Nov 12, 2012, 08:00 PM
Robert R is offline
Find More Posts by Robert R
It's a fine fiddly business.
Robert R's Avatar
Very nice build.
RCG Plus Member
Latest blog entry: Mustang Sally Sea Trials
Old Nov 18, 2012, 12:51 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
Thanks Robert, I have been searching for a 1/8 scale figure. Preferably, one of Lindberg to have for display with the model plane. I've not had much luck. Any ideas?
Old Nov 19, 2012, 06:29 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
I tend to bounce around on a project, moving from one thing to another. Satisfied one wheel was done, we proceeded to the cowl. Now it's back to the other wheel.
I wonder if that's a form of ADD.
The wood structure of the cowl and forward fuselage will not be finished smoothly, since they will be aluminum sheeted. Glad I was talked out of the foil tape sceme!
Last edited by phillip57; Nov 20, 2012 at 01:04 PM.
Old Nov 19, 2012, 06:35 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
***
Old Nov 20, 2012, 10:54 AM
E-Challenged is offline
Find More Posts by E-Challenged
Registered User
E-Challenged's Avatar
With a highly valued model like this, I would use only the best RC gear I can get with emphasis on adequate and reliable power to the receiver and servos. ( maybe a flight battery pack instead of relying on a built-in or add-on switch-mode BEC)
Old Nov 20, 2012, 11:43 AM
phillip57 is offline
Find More Posts by phillip57
Registered User
Quote:
Originally Posted by E-Challenged View Post
With a highly valued model like this, I would use only the best RC gear I can get with emphasis on adequate and reliable power to the receiver and servos. ( maybe a flight battery pack instead of relying on a built-in or add-on switch-mode BEC)
Been using E-Flight motors with Castle Thunderbird esc's and Spectrum rx's without incident. The intention is the same on this model.
Old Nov 20, 2012, 01:11 PM
Jim Young is offline
Find More Posts by Jim Young
Designer/Builder
Jim Young's Avatar
Excellent work on the wheels.

-Jim
Old Nov 20, 2012, 01:20 PM
Chompwat is offline
Find More Posts by Chompwat
Tally Ho Chaps!
Chompwat's Avatar
I don't know if you can get this in the US,but its light, inexpensive and looks really good. I would imagine its easy to work with.

Scroll down until you reach Metalcoat.

http://www.mickreevesmodels.co.uk/~m...ccessories.htm
Old Nov 20, 2012, 03:33 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
Quote:
Originally Posted by Chompwat View Post
I don't know if you can get this in the US,but its light, inexpensive and looks really good. I would imagine its easy to work with.

Scroll down until you reach Metalcoat.

http://www.mickreevesmodels.co.uk/~m...ccessories.htm
Thanks for the lead Gavin, do you know of the metalcoat is sheet like? Or more of a foil? I am convinced that I can do a decent job with beverage can aluminum.
Old Nov 20, 2012, 04:22 PM
Chompwat is offline
Find More Posts by Chompwat
Tally Ho Chaps!
Chompwat's Avatar
Quote:
Originally Posted by phillip57 View Post
Thanks for the lead Gavin, do you know of the metalcoat is sheet like? Or more of a foil? I am convinced that I can do a decent job with beverage can aluminum.
I've seen self adhesive aluminium foil before but this looks a little heavier. It seems to hold its form as it comes off the roll and looking at that model EE Lightning has a degree of strength that foil wouldn't have. The only stockist I can find on the web is Mick Reeves in the UK.
She' coming along nicely Phil. You certainly have risen to the challenge!
Old Nov 20, 2012, 09:04 PM
E-Challenged is offline
Find More Posts by E-Challenged
Registered User
E-Challenged's Avatar
Quote:
Originally Posted by phillip57 View Post
Been using E-Flight motors with Castle Thunderbird esc's and Spectrum rx's without incident. The intention is the same on this model.

Sorry!, my comment was intended for a different build thread about a Proctor Jenny. Glad you are using good stuff for the SOSL model also.
Old Nov 21, 2012, 04:32 PM
Dennis Sumner is online now
Find More Posts by Dennis Sumner
Wanted for breaking Ohm's Law
Dennis Sumner's Avatar
Hey Phillip,

Great build, I see you live in SE Michigan. Have you gone to Midwest RC's MidAm? We would love to see it fly in person at next years MidAm.

Denny
Old Nov 21, 2012, 05:20 PM
phillip57 is offline
Find More Posts by phillip57
Registered User
Never been... I'll send PM.
Old Nov 21, 2012, 06:20 PM
Dennis Sumner is online now
Find More Posts by Dennis Sumner
Wanted for breaking Ohm's Law
Dennis Sumner's Avatar
It is a great laid back fly in with a steak sandwich pot luck dinner Saturday. Ken Myers and Keith Shaw have been doing this for 28 short years!

I have enjoyed the fun of electric flying only since around 2000 but really like to work and support this event. Another great lad back fly in is the Keith Shaw Birthday Fly in in Coldwater that Dave Griffe CD's

Denny


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Question Spirit of St Louis Hossinarizona Scale Kit/Scratch Built 5 Sep 21, 2012 08:03 PM
For Sale Spirit of St. Louis SC Johnson Aircraft - Electric - Airplanes (FS/W) 0 Aug 26, 2012 02:31 PM
Discussion Spirit of St. Louis / Cub STRINGFLY Scale Kit/Scratch Built 1 Aug 04, 2012 02:08 PM
Sold Spirit of St.Louis by Graupner jricchio Aircraft - Electric - Airplanes (FS/W) 2 Jun 18, 2012 08:28 PM
Wanted Flyline Spirit of St. Louis apage Aircraft - Fuel - Airplanes (FS/W) 1 Jun 05, 2012 09:31 AM