Thread Tools
Dec 06, 2012, 01:32 PM
Videopilot
Derek_S's Avatar
Quote:
Originally Posted by Truglodite
Derek, welcome and sorry to hear it still isn't working. Are you using Arducam 2.0 firmware? It has an issue with panel 2 switching anyways. There is also the minimosd-extra project you might want to check out; seems to be a more active than Arducam, and a similar panel 2 problem was already fixed a few releases ago. In fact I plan on installing minimOSD-extra before Sunday. I like Arducam as it seems to be less invasive on the APM telemetry parameters, but until that panel 2 issue is fixed it is almost useless to me.

Jumpy, thanks for the info on the radio settings. I'm running the defaults from the 3dr firmware with airspeed=64 and both ecc and op resend checked. I also increased my Tx power up to the max value of 20. ECC doesn't help on the air system end? I'll uncheck those 2 boxes if they don't help range.

Kev
I was using Arducam 2.0, but last night uploaded it with MinimOSD-Extra 2.1. Still doesn't work with that firmware, so may try a older version like 1.9 tonight.
Sign up now
to remove ads between posts
Dec 07, 2012, 05:31 AM
Registered User
Quote:
Originally Posted by Jumpy07
Rctimer are shipping plug and play cables for 3DR Radio's and GPS now with the APM 2.5 clone

http://www.rctimer.com/index.php?gOo...8&productname=
Anybody know where I can get these cables in the US?
Thanks
Bob
Last edited by hobbyboy; Dec 07, 2012 at 06:04 AM.
Dec 07, 2012, 05:43 AM
FAA Certified Pilot
Quote:
Originally Posted by hobbyboy
Anybody know where I can get these cables in the us?
Thanks
Bob
I am an RCTimer Dealer.....I sell the boards too.....but I'm out of stock

I have an inventory order going out on December 10th
Delivery in the US will be December 18th

Pre-Orders accepted

www.uavobjects.com

Send me a PM and I will see what I can do
Dec 07, 2012, 05:48 AM
WannaBeLikeJoshTheSlowJet
bakchos's Avatar
anyone can please share there setting for a spider frame quad, i just need a starting point since im new to APM

thanks
Dec 07, 2012, 06:32 AM
Registered User
Quote:
Originally Posted by RYBAT
I am an RCTimer Dealer.....I sell the boards too.....but I'm out of stock

I have an inventory order going out on December 10th
Delivery in the US will be December 18th

Pre-Orders accepted

www.uavobjects.com

Send me a PM and I will see what I can do
PM sent.

Bob
Dec 08, 2012, 12:38 PM
AMA 993956 IMAC 7030
Mavlar's Avatar

Need help Please with my JR10x Mixing


Hi There
Anyone know how to mix 2 switches on the JR 10X Air to get the 6 modes? It is driving me nuts I cant seem to get all 6 modes for the Mission planner just 4.

Any help will be great
Thanks
Tom
Dec 08, 2012, 01:07 PM
Always learning..
Jumpy07's Avatar
I have updated my Guide.. current version V1.3

https://www.rcgroups.com/forums/show...5&d=1354993533
Dec 08, 2012, 06:17 PM
Registered User
flyboygaac's Avatar
Quote:
Originally Posted by Truglodite
LOL, I think most are using telemetry instead of bluetooth.

Kev
I agree, but Bluetooth has its advantages, and more people will post this question again on how to connect the bluetooth to the APM 2.5 in UART0 or 2?
Dec 08, 2012, 06:50 PM
Videopilot
Derek_S's Avatar
HAve you tried it at all? With a little googling I cant find your answer, but it looks like it shouldnt be too hard, and some posts I see imply people are doing it successfully. I just wonder if it can connect to the telemetry port or if you need to have a breakout harness form the usb port.
Dec 08, 2012, 08:51 PM
Future-proof EVERYTHING
DarkHeli's Avatar
Im trying to connect telemetry and minimOSD. I understand the RX only needs to be connected from osd but do I have to splice the rx into the 3dr telemetry or can I use a different UART port for minimosd and the original for the telemetry?
Dec 09, 2012, 11:12 AM
Still flying
Ramnes's Avatar
Quote:
Originally Posted by DarkHeli
Im trying to connect telemetry and minimOSD. I understand the RX only needs to be connected from osd but do I have to splice the rx into the 3dr telemetry or can I use a different UART port for minimosd and the original for the telemetry?
I'm not very good with electronics, but i'm learning. So bear over me if this is totaly wrong.
I was also thinking of doing that, but it seems like uart0 and uart2 are the same. But there is a AutoMUX uart0 there which i hope'd i could solder to split those uarts and use uart0 pins for the MinimOSD.

A drawing to a novice would help if this came out bad

J
Dec 09, 2012, 03:20 PM
Still flying
Ramnes's Avatar

New Fatshark predator V2 and minimOSD


Hi
I'm planning on buying the New Fatshark predator V2, and wonder if anyone has tried to connect them with the APM2.5 and the MinimOSD?

I found a post over at diydrones which had an issue not seeing whats on the lower part of the screen, but that was in january and could have been fixed by now.

J
Dec 09, 2012, 03:37 PM
Always learning..
Jumpy07's Avatar
Quote:
Originally Posted by Ramnes
Hi
I'm planning on buying the New Fatshark predator V2, and wonder if anyone has tried to connect them with the APM2.5 and the MinimOSD?

I found a post over at diydrones which had an issue not seeing whats on the lower part of the screen, but that was in january and could have been fixed by now.

J

I have the new SD Attitudes...and they work fine..

There are some issues with MinimOSD v1.0 with hires cameras.. which I think displays the problems you describe.... I have to reset the MinimOSD after power on to get OSD overlay with my 600tvl WDR

This is quite a common problem.. but not one that seems to exist if you use a 520tvl or lower camera..
Dec 09, 2012, 03:49 PM
Still flying
Ramnes's Avatar
Quote:
Originally Posted by Jumpy07
I have the new SD Attitudes...and they work fine..

There are some issues with MinimOSD v1.0 with hires cameras.. which I think displays the problems you describe.... I have to reset the MinimOSD after power on to get OSD overlay with my 600tvl WDR

This is quite a common problem.. but not one that seems to exist if you use a 520tvl or lower camera..
Thanks Jumpy07
I have the MinimOSD 0.1 from China. I've followe your APM2.5 manual setting up my APM, with 433Mhz telemetry and now maked the cable from APM to MinimOSD. Your manual is easy to follow when youre a newbie.

J
Dec 10, 2012, 07:58 AM
Videopilot
Derek_S's Avatar
Quote:
Originally Posted by Ramnes
Thanks Jumpy07
I have the MinimOSD 0.1 from China. I've followe your APM2.5 manual setting up my APM, with 433Mhz telemetry and now maked the cable from APM to MinimOSD. Your manual is easy to follow when youre a newbie.

J
OT, but did you get you China MinimOSD to work? Still cant get past the "waiting for heartbeats" on mine, after exhausting all troubleshooting options that I can find. Doesnt seem likely, but wondering if it is a bad OSD...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold 3DR APM 2.5 + Ublox Gps Zenonic Aircraft - Electric - Multirotor (FS/W) 4 Oct 01, 2012 09:32 AM
Sold 3DR APM 2.5 + Ublox Gps Zenonic Aircraft - Electric - Airplanes (FS/W) 0 Sep 28, 2012 10:58 PM
Sold Apm 2.5 and Gps Panzlflyer FPV Equipment (FS/W) 2 Sep 26, 2012 08:30 AM
Sold APM 2.5 with Ublox Gps Panzlflyer Aircraft - Electric - Multirotor (FS/W) 0 Sep 25, 2012 07:03 PM
Discussion APM 2.5 clone - MegaFlight 2.5 ralphwu Multirotor Drone Electronics 1 Sep 24, 2012 01:18 PM