DiaLFonZo-Copter - MiniSpyder - Page 5 - RC Groups
Thread Tools
Nov 16, 2012, 08:16 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by danger_mouse
Eric, what sized board cam fits up front with the optional ccd mount plate?
If i remember right it's 34mm mounting max but have slot for smaller

Yoy have a size in particular?
Sign up now
to remove ads between posts
Nov 16, 2012, 08:25 PM
Registered User
eDoug's Avatar
Quote:
Originally Posted by Dialfonzo
If i remember right it's 34mm mounting max but have slot for smaller

Yoy have a size in particular?
It is the PZ0420 from Security2000. I have trimmed the outer part, so 32mm across.

Nov 16, 2012, 09:11 PM
Team Armattan
Quote:
Originally Posted by danger_mouse
I have the C20's on my 200mm quadrixette nano. Around 4 to 1 thrust ratio with 5x3x3 props. ~335grams thrust per motor. Uses 100mah per minute in flight. Supposed to be good for up to around 550 grams thrust with 7 inch props.

They go well. Just make sure the grubscrew securing the shaft to the bell is threadlocked. Had one motor where the shaft slipped. Wouldn't hurt to disassemble and grind a flat on the shaft.



Cool. What flight controller you running? Was it easy to tune? I found with my little overpowered quad it was real fussy on the PID tuning.
On this one I am running a Crius Multiwii SE no problem tuning so far.

Dialfonzo Mini Spyder (5 min 26 sec)
Nov 16, 2012, 09:49 PM
Registered User
eDoug's Avatar
Nice. Angry little thing when you open it up..

What happened around the 7-8 second mark?
Nov 16, 2012, 09:51 PM
Some call me the other guy!
DoctorAudio's Avatar
hahahah, it is a beast!
Nov 16, 2012, 10:14 PM
Team Armattan
Quote:
Originally Posted by danger_mouse
Nice. Angry little thing when you open it up..

What happened around the 7-8 second mark?
called clumsy thumbs as I explained on YT I am running at 40% expo and 80% D/R and it is still mighty responsive as soon as I get out to the open field I will let it fly.
An oh that is probably a little less than 3/4 open throttle. Do not want to put it through a neighbours window.
Nov 16, 2012, 10:35 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by danger_mouse
It is the PZ0420 from Security2000. I have trimmed the outer part, so 32mm across.

[]http://www.securitycamera2000.com/CCTV/Camera/PZ0420-2-600TVL-board-camera.jpg[/IMG]
There are 4 slot in the corner.
Each have a maximum of 34mm and a minimum i will look tomorrow.

But i am sure it will fit. Unless i will make you a custom one..
Nov 17, 2012, 08:17 AM
Registered User
I am thinking of trying 5.5x4.5 speed props. They will be easier to balance. and maybe more durable in crash......"not that I crash, I am perfect"

Quote:
Originally Posted by danger_mouse
I have the C20's on my 200mm quadrixette nano. Around 4 to 1 thrust ratio with 5x3x3 props. ~335grams thrust per motor. Uses 100mah per minute in flight. Supposed to be good for up to around 550 grams thrust with 7 inch props.

They go well. Just make sure the grubscrew securing the shaft to the bell is threadlocked. Had one motor where the shaft slipped. Wouldn't hurt to disassemble and grind a flat on the shaft.



Cool. What flight controller you running? Was it easy to tune? I found with my little overpowered quad it was real fussy on the PID tuning.
Nov 17, 2012, 09:10 AM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar

CCD - Plate


I have made some minor modifications to the plate this morning.
The hole in the middle was a bit too small for mine because i want it close to the plate and there is a plastic casing that is bigger than the lens.

Here are the dimensions
Nov 17, 2012, 01:13 PM
Registered User
Mine will be here in two days. I am ready!!!
Nov 17, 2012, 04:36 PM
Some call me the other guy!
DoctorAudio's Avatar
danger_mouse: remember you don't have to screw it in!
I am just going to put some doublesided foam on the front side and then use two bubber bands around the mount.
Nov 17, 2012, 05:40 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Will cut and assemble to show tomorrow
Nov 18, 2012, 11:26 AM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar










Nov 18, 2012, 06:24 PM
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
On a spyder made of wrongly cut parts....

Nov 21, 2012, 03:55 PM
Registered User
It came today!
It is easy to put together. You can put it together with a 4 month old on your lap


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion DiaLFonZo-Copter Crazy2Fly Quadcopter 340mm Dialfonzo Multirotor Drone Talk 87 Feb 07, 2016 07:41 AM
Build Log Unrealistic's HEXorcism 600 - Luis & DiaLFonZo-Copter unrealistic Multirotor Drone Talk 47 Oct 23, 2012 05:09 AM
For Sale DiaLFonZo-Copter TrinityHEX - ReList Dialfonzo Aircraft - Electric - Multirotor (FS/W) 3 Apr 27, 2012 03:44 PM
For Sale DiaLFonZo-Copter TrinityHEX - USED Dialfonzo Aircraft - Electric - Multirotor (FS/W) 7 Apr 20, 2012 12:34 PM