Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
This thread is privately moderated by GeetarJoe, who may elect to delete unwanted replies.
Old Oct 08, 2012, 04:47 PM
GeetarJoe is offline
Find More Posts by GeetarJoe
Trader Rating: 48
Who Dat!
GeetarJoe's Avatar
For Sale

Lots and Lots of Carburetors!


All are for sale. $50 Each for the Walbros and $40 for the Zamas.

Warlbo F8/WA 144 Carb: 11.11mm
https://www.rcgroups.com/forums/show....php?t=1650267

Walbro HDB6B Carbs new or like new
https://www.rcgroups.com/forums/show....php?t=1650266

Walbro Carbs WT610 new or like new 13mm
https://www.rcgroups.com/forums/show....php?t=1650264

Walbro Carbs WT529 New or like new 13mm
https://www.rcgroups.com/forums/show....php?t=1650263

Walboro HDA110 13.49mm
https://www.rcgroups.com/forums/show....php?t=1650195

Zama C1Q ~40cc 12.5mm
https://www.rcgroups.com/forums/show....php?t=1650258

Notice: The previous threads have been closed in order to keep all of the replies in one place. Please PM me if interested.
Last edited by GeetarJoe; Oct 10, 2012 at 05:47 PM.
Sign up now
to remove ads between posts
Old Oct 09, 2012, 10:21 AM
redball8 is offline
Find More Posts by redball8
Trader Rating: 180
What - Me Hurry?
redball8's Avatar
GeeTar, ever run across a Del'lorto carb? I have a few OPS 30cc Maxi's that use them, and have heard that Walbro carbs are bolt-on replacements. I wondered which Walbro would fit? And can you run a Walbro carb on glow fuel?

Thanks, RB8
Old Oct 09, 2012, 03:21 PM
GeetarJoe is offline
Find More Posts by GeetarJoe
Trader Rating: 48
Who Dat!
GeetarJoe's Avatar
you can but you have to change the pump diaphragm to the teflon or acetate one that comes in the rebuild kit. what is the venturi diameter of the stock carb? im sure one of these carbs will work. probably the WT610.
Old Oct 09, 2012, 08:55 PM
redball8 is offline
Find More Posts by redball8
Trader Rating: 180
What - Me Hurry?
redball8's Avatar
The Del'Lorto carb has a 10 mm venturi diameter.

It also has this port on the carb mounting base for crankcase pressure, to operate the diaphragm. Is that pretty standard on pumper carbs?
Old Oct 10, 2012, 12:14 AM
GeetarJoe is offline
Find More Posts by GeetarJoe
Trader Rating: 48
Who Dat!
GeetarJoe's Avatar
Yes. The crankcase pulse is required to get these carbs to work. If the walbro is a bolt on then the pressure port is likely to be in the right place. Even if its not you can tap the case and run the pressure line externally. The pressure port is in the same place on all standard walbro carbs.

Im about to hit the bed, early day tomorrow. But if you can hang tight until tomorrow evening i will break out the calipers and measure out these carbs. Im certain i have one with a 10mm venturi.
Old Oct 12, 2012, 08:26 PM
High & Mighty is online now
Find More Posts by High & Mighty
Trader Rating: 30
Registered User
High & Mighty's Avatar
13.49 MM is the venturi diameter or .531" which equals 17/32".

The OPS Maxi 30 is a beast and I'm sure a 10mm venturi is not enough to feed it.
Old Oct 13, 2012, 02:06 AM
brown2x2 is offline
Find More Posts by brown2x2
Trader Rating: 4
Registered User
brown2x2's Avatar
hii

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Small Engine/Carburetor Cleaner PyroMan Beginner Training Area (Fuel) 7 May 06, 2012 02:39 PM
Sold Royal .40 Carburetor N925WB Aircraft - Fuel - Engines and Accessories (FS/W) 2 Apr 09, 2012 08:38 AM
Discussion No more carburetors kenh3497 Engines 28 Apr 06, 2012 08:26 PM
Sold Lighty used O.S. Carburetor 61E For 91HZ bbq4good Aircraft - Fuel - Engines and Accessories (FS/W) 1 Mar 19, 2012 08:29 PM
Found New or used Carburetor needed J.A.Bairos Aircraft - Fuel - Engines and Accessories (FS/W) 0 Mar 09, 2012 06:45 PM