I did what I could - RC Groups
Thread Tools
Oct 07, 2012, 12:05 AM

I did what I could

OSD Pro Board is not connected. Please connect the OSD and try again.

It his message keeps appearing and I did everything the trouble shooting says, what else can I do!!!!!

It was working fine then all in set it this is what I been getting!!!!
Sign up now
to remove ads between posts
Oct 08, 2012, 02:17 PM
billpa's Avatar
Hi, sorry to hear about your issue.

If you connect your OSD Pro to your eLogger, connect the eLogger to USB, and click "Hardware, Firmware Control" in the software, does the Firmware Control page show the OSD and eLogger as connected?
Oct 08, 2012, 03:10 PM
Yes it does, and now I can't even get the led to flash anymore but I do see the OSD connected to the pc, and it transmit signal to the screen, but the logo reminds there and will not go away,
Oct 08, 2012, 07:29 PM
ok i got the LED back to work, but pc will not even open it, like if i have not conected the Logger,!!!!!!!!
Oct 09, 2012, 12:55 AM
damn you tree!
roballoba's Avatar

helping Aisamac

when working on Aisamac's OSD pro, it would not work.

latest beta software loaded to windows 7 64bit pc.

We got the elogger plugged into computer with the firmware to updated to 1.21
the on board led blinks 3 times to indicate it is connected.
with nothing else connected to the elogger, we get live view mode to work showing us battery voltage.

when we plug in the OSD pro to elogger, (without it plugged to computer,) on the pins closest to the usb plug (closest to the label side) I assume this is the bottom, we get video transmission to work. The video passes through, but there is no data on the screen. (plugged to middle pin set, the eagle tree logo is transmitted, but only when connected to computer with usb. plugging OSD into top? pin set does nothing, but I assume this is the GPS spot - label is unclear as to what is top or bottom.

when plugged to usb, the computer flashes msg that USB device is not recognized.
in the eLogger software, the firmware control does not recognize the osd, or any other device.
when we go to live view, the software stated osd is not connected.
when we unplug the osd, the live view works.

it's not happy.
Oct 09, 2012, 01:55 PM
billpa's Avatar

It sounds like you may have the OSD pro connected incorrectly. Please refer to the attached drawing. Is this how you have it connected?
Oct 09, 2012, 02:19 PM
We connected as the graphic and the screen is black and the OSD caused the eloger to crash the PC,

I really think this is a product that is faulty and needs to be replaced!!
Oct 09, 2012, 02:28 PM
billpa's Avatar
Hi, if the PC software is hanging/crashing when connected as above, I agree that there is an issue with the hardware. Please open a ticket with us at http://ticket.eagletreesystems.com and we will check both the eLogger and OSD Pro, and get the issue sorted for you.
Oct 09, 2012, 02:30 PM
793773 is being done Man,

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion what could cause a belt to get lose and what can i do wc_wickedclown Electric Heli Talk 6 Jun 23, 2012 04:01 AM
Help! What could be a problem? man1024 Multirotor Drone Talk 6 Jun 06, 2012 10:45 AM
Discussion what could cause my align esc not to make the arming beep. wc_wickedclown Electric Heli Talk 14 May 23, 2012 11:27 AM
Discussion What Could Possibly Go Wrong? Real Ira Life, The Universe, and Politics 0 Apr 02, 2012 04:02 PM