Thread Tools
Old Oct 05, 2012, 08:16 PM
AeroKen is online now
Find More Posts by AeroKen
3D? I only got two thumbs!
Discussion

Initial charge - 6 in parallel or one by one?


Just got 6 new glacier lipos. Also just got set up to charge in parallel. So I'm wondering, is it prudent to charge all 6 in parallel (at 1C for the initial charge), or would it be better to do them one at a time to monitor them better?

Hm, maybe I just answered my own question. But I'm still curious what others do.

I plan to do 2 charge / discharge cycles to break them in, then weather permitting Sunday charge them up, head to the field, and discharge them the fun way - in an airplane.
Sign up now
to remove ads between posts
Old Oct 05, 2012, 09:13 PM
TheWoodCrafter is offline
Find More Posts by TheWoodCrafter
RC Helicopter Pilot
TheWoodCrafter's Avatar
I never brake in new LiPo with parallel charging.
Always charge them one at a time.
Old Oct 05, 2012, 09:16 PM
everydayflyer is offline
Find More Posts by everydayflyer
Southern Pride
everydayflyer's Avatar
Quote:
or would it be better to do them one at a time to monitor them better?
Yes

Quote:
I plan to do 2 charge / discharge cycles to break them in,
Unless you charger can place a discharge load on them enough to cause them to warm up you will be wasting your time,IMO.

Many chargers have a 50 watts or less discharge capability , whith a 3S this is approx. 4A which for a 2200 is less than 2C and it will not get warm at all.

Just charge them and fly them taking it easy the first few flights, short burst of WOT and keep flights short so only 60 % or so is used , 3.8 V per cell after flight.

Charles
Old Oct 05, 2012, 09:27 PM
AeroKen is online now
Find More Posts by AeroKen
3D? I only got two thumbs!
Thanks guys I'll do them one at a time.

Quote:
Originally Posted by everydayflyer View Post
Unless you charger can place a discharge load on them enough to cause them to warm up you will be wasting your time,IMO.

Many chargers have a 50 watts or less discharge capability , whith a 3S this is approx. 4A which for a 2200 is less than 2C and it will not get warm at all.

Just charge them and fly them taking it easy the first few flights, short burst of WOT and keep flights short so only 60 % or so is used , 3.8 V per cell after flight.

Charles
Yup these are 3S 2200 35C.

I'm in the process of soldering up some switches and 50w 12v halogens to use for discharging. With 6 50w bulbs I should be able to pull 24+ amps, and by cutting out a few switches control that in 4 amp increments to get whatever current I want. What is a good breakin discharge current? I seem to recall reading 10C?
Old Oct 05, 2012, 09:37 PM
mrforsyth is online now
Find More Posts by mrforsyth
Registered User
I break-in at 5-8C. 10C is starting to push it, IMO. I also perform IR and capacity measurements prior to placing a lipoly into service. If they don't meet my expectations, back they go for replacement or refund.

Mark
RCG Plus Member


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Wanted Charge adapters to charge 1s 200mah Eflite batteries in parallel MolokaiBoy Aircraft - Electric - Batteries & Chargers (FS/W) 0 Aug 15, 2012 10:36 PM
Discussion Charging from one 80 Ah 12 volt Pb battery at the time or two in series? bossee Batteries and Chargers 10 Jun 26, 2012 07:18 AM
For Sale Xt-60 6-port parallel charge board 3drcparts Aircraft - Electric - Batteries & Chargers (FS/W) 1 Jun 23, 2012 10:44 PM
Sold banana to 6 jst parallel charge cord $12 shipped 3drcparts Aircraft - Electric - Batteries & Chargers (FS/W) 2 Jun 18, 2012 10:59 AM
Discussion Larger charger and charge in parallel, or 4-port charger individually? NeveSSL Batteries and Chargers 13 May 18, 2012 10:31 AM