Horizon Hobby ParkZone Albatros D. Va BNF Review - RC Groups

Horizon Hobby ParkZone Albatros D. Va BNF Review

Parkzone has followed up their nice flying SE5a WWI allied fighter plane with the beautiful German Albatros D. Va. This review covers the assembly and flight characteristics of this striking WWI fighter plane.



Wingspan:42.3" top wing
Weight:43.4 oz.
Length:35 inches
Propeller:10 x 8
Servos:2 digital & 2 analog servos installed
Transmitter:Spektrum DX7s
Receiver:Spektrum AR600
Battery:3S 1800mAh 15C LiPo
Motor:960kV-480 electric Brushless
ESC:EFL 30A Pro SB Brushless ESC
Available From:Horizon Hobby
Price:$249.99 BNF

The ParkZone Albatros D. Va showed up in the hands of another pilot at our flying field and it: "Looked Marvelous!" I started tracking it with my camera and took some pictures and loved what I was seeing. The plane handled well and had plenty of power to perform nice aerobatics including loops, rolls, S turns, spins and more. With nice scale looks and good performance already known factors for me I jumped at the chance to review it. No surprise during this review just more details. I love this plane. Now for the rest of the story.

Kit Contents

Kit Includes

  • Top wing with two servos installed
  • Bottom wing
  • Fuselage with motor, prop, ESC, two servos and pilot with scarf installed
  • Landing gear and wheels
  • Wing struts and hardware
  • Instruction manual
  • 3-cell 1800mAh LiPo battery pack
  • LiPo Charger



The wings came fully assembled but they needed to be attached to the fuselage and struts needed to be attached between the outer sections of the wing. These wing attachments to the fuselage are discussed below in the Fuselage Section.


Installing the Lower Wing and Landing Gear onto the Fuselage

Per the instructions I started with the bottom of the fuselage facing up and the lower wing facing down. A tongue in the front of the lower wing slid into the front of the wing saddle and the back of the wing was secured to the fuselage with two 3 x 10mm screws.

With the lower wing installed the landing gear was then assembled following the instructions. The landing gear is made up of metal and plastic parts and they are held together with four 1.5 x 6mm screws at the axle cross piece.

The landing gear has four metal wire pins that fit into the fuselage and these metal mounts were then secured in place with four mounting brackets that were secured with two 2.5 x 8mm screws each.

Mounting the Top Wing onto the plane

The Cabane struts have two plastic parts at the top that slip into L brackets molded into the wing. Once in the wing's L brackets the Cabane struts were rolled into position. The Cabane struts were then secured to the side of the fuselage with two 3 x 10 screws to each side of the fuselage. With the top wing now secured to the fuselage I plugged in the two servo wires into the two female plugs extending up from the fuselage. It was now time to install the outer wing struts.

The outer wing struts install into the top side of the lower wing just as the Cabane struts were secured into the upper wing only this time there is only one piece and one L bracket per wing side. The outer wing struts were rotated up and slipped into mounting pieces on the underside of the top wing and there they were secured to the top wing with a retainer pin on each side. Very simple process and a nice design for the assembly.

Radio Installation

Since it was necessary to move the rudder to one side to install the vertical stabilizer and elevator I decided to bind the receiver before installing the vertical stabilizer. A binding extension wire runs from the receiver into the battery bay that is accessed in the front bottom of the fuselage. I connected the supplied binding plug into the extension wire ant with my DX7s transmitter by me I connected the flight battery pack to the ESC and bound the receiver to an available channel on my transmitter. Once that was complete I held the rudder over for a hard right turn and disconnected the battery pack from the ESC with the rudder extended out hard to the right.

After the Albatros was fully assembled and the elevator control horn connected to the elevator control rod; I came back and made sure all the servos were moving in the proper control directions.


The horizontal stabilizer slid onto the back of the fuselage in a molded form that nicely aligned the horizontal stabilizer with the fuselage and the wings. The stabilizer was then secured in place with one screw that is mounted right under the rudder when it is in the neutral position. Since I had it turned out to a hard right position I was able to install the mounting bolt through the vertical stabilizer and into the fuselage. With the stabilizer secured in position I connected the elevator control rod to the elevator control horn on the elevator.

The last portion of the assembly required a decision by me of which tail option to use. A plastic tail piece with a tail skid is one option and would be more scale like. The other option allowed me to install a steerable tail wheel to my Albatros. The tail skid piece is secured to the underside of the fuselage with four supplied 1.5 x 8mm screws. The tail wheel mount required me to disconnect the rudder control horn and snake the top of the landing gear wire from below, through a slot molded into the vertical stabilizer and then place the top of the wire into the rudder control horn position and secure it by reattaching the control horn back into position and securing the plastic tail wheel mount under the fuselage with that optional mount using the four supplied 1.5 x 8mm screws.


With the battery charged I installed it into the battery bay on the front underside of the fuselage and checked to make sure the plane had the proper Center of Gravity (It did!) and adjust the throws on my transmitter to make sure they matched the recommendations for both low and high rates.



The Albatros has four channel control with throttle, ailerons, elevator and rudder. The plane can be flown without using the rudder but I strongly recommend that you use the rudder and use it sometimes without the ailerons as I get slides from my Albatros that seem very appropriate for a World War I fighter plane. Flying with a combination of ailerons rudder and elevator give the best control and allows me to fly the Albatros very smoothly with small movements to wild with full throttle and full stick movements. With low rates and flown smoothly she handles like a nice Sunday fighter, I mean flyer. Put an SE5a in the air and we can have a great mock dogfight. In fact ParkZone has thought about just that possibility. They sell Sonic Combat Modules that let you have combat between the Albatros and the SE5a. I have used their previous combat modules sold for prior planes and they worked very well. If I find an opponent with an SE5a I will see if he is interested in getting the modules and mixing it up with our planes. I am sure it will be fun from past experience with other planes. On basic flight the motor supplies lots of power at full throttle and I prefer to adjust the throttle and mix slow flight with full throttle flight. It gives slightly longer flight times and to me it makes the fast bursts seem even faster than just going full out for long periods.

Taking Off and Landing

As with any biplane cross wind takeoffs and landings in a strong breeze can cause the down wind side of the bottom wing to touch the ground at times. I avoid this by taking off and landing into the wind and have had no problems doing so. Takeoffs can be achieved in 15 feet or less or done more slowly can be done in a more scale like fashion. I fly off of dirt as seen in the video and off of pavement. I only fly off of grass on occasion and have not yet done so with my Albatros. Landings have been smoothest when landing with some throttle on and this is especially true in soft dirt. I don't land with the motor off but those that due tend to nose over a bit unless they properly flair just before touch down. She is not a hard plane to takeoff or land into the wind. In a mild cross wind the rudder has proven effective in letting me steer the plane down the runway. In a higher wind it is fun to make passes down the runway while holding against the rudder alone against cross wind. However when landing I will try to make a landing as straight into the wind as I can.

Aerobatics/Special Flight Performance

With its four ailerons the SE5a appeared to me to be a bit more agile in turning when I observed it flying by itself. However, when chasing an SE5a or being chased the Albatros proved to be very agile in our mock combat exercises. As stated in the introduction the Albatros has proven to be a very acrobatic plane. At full throttle and starting from a shallow climb I can do nice back to back aileron rolls. A nice large half loop transitioning to a dive with an S-turn looks great. With power on low a vertical dive with spin looks like a death spin. To get out just apply throttle, counter rudder and up elevator. (I was sure to give myself a lot of air space beneath my plane when first trying this trick.) I started flying a little bit higher and performing stunts at lower speeds and obtained some waddle in the air that looked realistic to my eye for how I thought a real Albatros might have flown.

Is This For a Beginner?

NO! This plane is recommended for an intermediate or better pilot. The detailed undercarriage (landing gear) is made with a combination of plastic and metal parts and is not designed for the kind of abuse many beginners would inflict on the landing gear. The plane is well behaved and an experienced pilot should have no problem handling the Albatros D. Va.

Flight Video/Photo Gallery


The first six pictures below were taken within a half hour of sunrise which can make for some interesting lighting. The rest of the pictures were taken mid-morning. This is a very photogenic plane and looks very pleasing to my eye throughout the flight.



I have found the ParkZone Albatros to be a very fun plane to fly. It handles nicely but flies differently from any of my other ParkZone fighters and that includes the SE5a which I don't own but have flown several times. In my normal flying I experienced no problems with the handling or performance of the Albatros. If I am flying too slowly and make too sharp a turn, I have stalled my Albatros but recovered easily as I did this with altitude that allowed for recovery. Just flying normally I have had no control problems at all. I think she looks great as sold but I appreciate the many colorful paint schemes posted by E-Zone members. I will paint the display engine on my Albatros to give added realism to my plane.

Pluses and Minuses


  • Assembly was quick and easy.
  • I like the designed hinges for connecting the struts to the top wing and lower wing.
  • The pins made connecting the outer struts to the top wing very easy and I don't notice them in flight.
  • The plane to this beholder looks great on the ground or in the air.
  • Easy to grab and take to the field ready to fly.
  • Optional tail skid/wheel depending on your flying field


  • One or two of the four landing gear assembly pins took real effort for me to push into the fuselage.


My thanks to Dick Andersen with the media in this review, ParkZone/Horizon Hobby for supplying the Albatros for review and our editor, Angela, for her assistance with this article.

Last edited by Michael Heer; Nov 22, 2012 at 09:29 PM..
Thread Tools
Nov 27, 2012, 02:56 PM
Registered User
MRGTX's Avatar
I love the dawn patrol pictures!!

Nice write up!!

It sounds like you were happy with the performance but do you think it flies too fast to appear "scale?"
Nov 27, 2012, 06:06 PM
Registered User
Michael Heer's Avatar
No! It can be flown at what appears to be scale speed! It can also be flown much faster. Up to the individual pilot to decide. Mike H
Nov 28, 2012, 07:53 AM
Go 4th Air Force
pmacko's Avatar
This is a very good review. My experience matches Michaels perfectly, right down the the landing gear pins being hard to push into the fuselage. I also have the PZ SE5 and they are indeed different so don't think that buying the second plane is the same experience

Nov 28, 2012, 09:25 AM
I Fly!
jrtubb's Avatar
Great Review. I have been enjoying my Albatros, it gets a bunch of looks from other pilots at the field.
Nov 29, 2012, 12:23 PM
Registered User
MRGTX's Avatar
Originally Posted by Michael Heer
No! It can be flown at what appears to be scale speed! It can also be flown much faster. Up to the individual pilot to decide. Mike H
This is extremely encouraging. OK... I want one.
Nov 29, 2012, 09:38 PM
Registered User
kevin whitesell's Avatar
Gents: i mostly have ww2 warbirds in my hanger(all electric pz and e-flite) I love my albetros the most because it's different than all the others i have.The alby is just a relaxing pleasure to fly. Also it flies very well-slow flybys at eye level are just beautiful. I have never regreted a penny spent on buying the pz alby. i LOVE MY ALBY SO MUCH -I DONT CARE WHAT THE WIFE SAYS-I MIGHT GET A TATOO OF IT ON MY SMELLY -HAIRY LITTLE BODY
Dec 02, 2012, 02:33 PM
Great review, and dead-on. I have 60+ trouble-free flights on mine, as of this morning--quite a " looker" against a sunrise and broken clouds. It can be flown very scale, looking for all the world like the reproductions flying at Old Rhinebeck. I can't wait to see the third in the series!
Dec 05, 2012, 11:11 PM
Go 4th Air Force
pmacko's Avatar
Originally Posted by GradyLee
I can't wait to see the third in the series!
Any idea what's coming next?
Dec 06, 2012, 05:36 AM
Originally Posted by pmacko
Any idea what's coming next?
Sadly, no. I doubt it would be a triplane, Camel or Nieuport, for balance reasons. I know most people doubt they'd do 2 German planes in a row, but I wouldn't be shocked to see a D-VII, which I think would fly (and sell) well. If it's not a D-VII then a SPAD, I think. I'll make room for whatever it is!
Dec 07, 2012, 11:46 PM
Registered User
I have one thats been weathered.....Pretty sweet plane!
Dec 11, 2012, 11:10 AM
I Fly!
jrtubb's Avatar
Michael can you take some measurements of the radiator tube that sticks up on the top of the wing? Close up pictures would be nice too as I had a mid air last week with my son and that is the only part missing from the wing after I repaired the damage with glue. Since I had some dents I ended up weathering the wings to help cover up the damage
Dec 11, 2012, 12:13 PM
Mattfly's Avatar

Here you go.

Hope this helps.

Matt Andren
Parkzone/Hobbyzone Product Development
Horizon Hobby.
Dec 11, 2012, 03:04 PM
I Fly!
jrtubb's Avatar
Excellent, that is what I was looking for! Wish I could just buy this part instead of a complete wing. This plane is great and survived our mid air better then any balsa plane I had from the 90s! Even my son's Firebird did fine considering the impact and altitude we were at. Please keep making great products!

Originally Posted by Mattfly

Here you go.

Hope this helps.

Matt Andren
Parkzone/Hobbyzone Product Development
Horizon Hobby.
Dec 13, 2012, 02:54 PM
Registered User
Michael Heer's Avatar
Thanks Matt for responding so quickly to the request. This really is a nice flying plane. Hopefully I will get a couple more chances to fly her again this year. I am in the process of of finishing up some indoor reviews but hopefully we will have some nice weather this Saturday and the Baron can get in a flight or two this weekend. Mike Heer

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Article Horizon Hobby ParkZone Ultra-Micro F4U Corsair BNF Review Spackles94 Micro Ready-to-Fly 18 Aug 01, 2012 12:09 PM
Article Horizon Hobby ParkZone Mk IX Spitfire BNF with Retracts Review Michael Heer Electric Warbirds 18 May 13, 2012 09:28 PM
Article Horizon Hobby ParkZone Ultra-Micro Pole Cat BNF Review sun.flyer Micro Ready-to-Fly 18 Feb 08, 2012 12:37 PM
Article Horizon Hobby ParkZone F-27Q Stryker BNF Review Tram Flying Wings 7 Nov 13, 2011 11:50 AM