Shop our Airplanes Products Drone Products Sales
Thread Tools
Oct 07, 2012, 07:23 AM
Registered User
KMOT has a thread here some place that he did a alsome job on his setup
But I cant find it I have the same boiler and engine that I bought 2 years ago
and it is still in the box
Bob Big
Sign up now
to remove ads between posts
Oct 10, 2012, 07:33 PM
made of fire and pop rocks
bgnome's Avatar
Quote:
Originally Posted by dostacos
well I figured out what you meant by soldering tabs {could not picture it until I started assembly} I think I will try that, it keeps the boiler from sliding up and down when it is removed from the fire pan where my method allows the boiler to move up and down when it is NOT attached to the board. I guess I could run some screws through the brass jacket {machine screws with nuts on the inside} either way it will lessen the ware and tear on da insulation!
yep, that is exactly the idea

I'm actually currently dusting off my elliot bay launch with this engine for some running around this coming weekend. Taking her out to bear creek lodge for the Brewer's big annual camp out drunk fes.. I mean, team building weekend

hopefully have some pretty pictures sometime next week.

my build for that boat is floating around somewhere in the archives but I didn't pay much attention to the engine build because I was transplanting from my older boat into the newer boat, and pretty much anything I did to it was already covered in Kmots build thread of his elliot bay launch with heritage engine.

This is Grumpa Toms build thread


this one is mine
Oct 10, 2012, 09:59 PM
Registered User
My friend and I found that adding extra holes to the brass which supports the boiler significantly increases power due to more oxygen to burn the fuel more efficiently.
Oct 11, 2012, 09:27 PM
some what irregular
dostacos's Avatar
Having just read KMOT's Elliot Bay build and dug out my fan tail launch. On another thread I joked about running the exhaust to a thru hull instead of into a condenser....well I just looked at my booklet and sure enough they show it going to a thru hull
Oct 11, 2012, 09:47 PM
made of fire and pop rocks
bgnome's Avatar
well... yeah...

it does

That's how I did the first one I built, followed the manufactures directions to a tee.
never much cared for it personally. and that's why I took advice and made changes based on the further experiments and findings of others more experienced than I on the matter.

its a good little engine for what it is and it's made even better with a few simple modifications.
Oct 12, 2012, 10:22 AM
Registered User
steamboatmodel's Avatar
Quote:
Originally Posted by dostacos
Having just read KNOTs Elliot Bay build and dug out my fan tail launch. On another thread I joked about running the exhaust to a thru hull instead of into a condenser....well I just looked at my booklet and sure enough they show it going to a thru hull
Running the exhaust through the hull side only works if you do not use a lubricator in the steam line.
Regards,
Gerald.
Oct 12, 2012, 10:44 AM
some what irregular
dostacos's Avatar
I MIGHT run it thru but only after the condenser.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
For Sale FY-X4 Pro Quad, motors, ESC, pre-assembled/soldered Blue Flyer Aircraft - Electric - Multirotor (FS/W) 1 May 04, 2012 06:22 AM
Question heritage steam r/cjunkie Steam Boats 10 May 22, 2011 12:00 PM
Wanted Midwest Model VI or Heritage Steam Engine bboarder711 Boats (FS/W) 0 Jan 06, 2011 08:20 PM
Discussion Midwest Heritage Steam Engine Frank Hurd Scale Boats 8 Aug 24, 2008 01:06 PM
For Sale Steam Engine Gage Tvr1a Assembled zorrow Boats (FS/W) 0 Sep 26, 2007 02:41 PM