Thread Tools
Old Sep 23, 2012, 12:39 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Discussion

DiaLFonZo-Copter - FPV SpyderQuad


Hi All,

Working on a FPV Spyder which share much of the DJI Upgrade center plates i have done.



I changed them to be able to use Round boom clamp (in my case the one i design to be 3D printed) but any 25mm clamp could be use (QuadFrame 16mm fit).

I have also included my landing motor mount that i have use on the BlackWidow Spyder .. So it's a bit of a mix and match frame.. lol
I have made the landing shorter.. to eliminate a bit of restriction while flying

Still it have a lot of work here and there.

There is a very simple CCD plate to be installed under.
This have a break-away center if you need to mount it on the back.. or front.
Leave it if you mount with soft double side tape.

I will build it 650mm motor to motor.. on the picture with the prop it's about that size.











RCG Plus Member
Sign up now
to remove ads between posts
Old Sep 23, 2012, 12:39 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
-- Reserved --
RCG Plus Member
Old Sep 29, 2012, 03:02 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
I have receive my custom 3D Printed boom clamp yesterday.
Here is a quick assembly with too short tube. (That's all i have on hand)

Waiting for some real nice 16mm tube from Matt at www.flycarbon.com

They will be already cut by him at 225mm.





RCG Plus Member
Old Sep 29, 2012, 08:05 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Some more pictures...











RCG Plus Member
Old Sep 29, 2012, 08:05 PM
Techcoder is offline
Find More Posts by Techcoder
Carbon Flyer
Techcoder's Avatar
Quote:
Originally Posted by Dialfonzo View Post
Waiting for some real nice 16mm tube from Matt at www.flycarbon.com
They will be already cut by him at 225mm.
This looks like a very sturdy design. Do the motor locations still form a square? It is nice to not have the blades in the way and still have the camera up high in a safe place. What is your popular FC of choice?
Old Sep 29, 2012, 08:19 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by Techcoder View Post
This looks like a very sturdy design. Do the motor locations still form a square? It is nice to not have the blades in the way and still have the camera up high in a safe place. What is your popular FC of choice?
No the motors are not in a perfect square.
It all start with a DJI arm center plate design HERE
Since DJI was all equal arm i have to deal with that .. And after fly it.. i didn't see any problem at all... lol

The assembly here have 140mm long boom ... cause that was all i have left.
But it will have 225mm CF.. you know..

This will be send to someone in Tahiti and the guy use NAZA flight controller.
I will build mine (the other one on the pic... ) with a NAZA too since i have one that is waiting in his box for some weeks..

But i do use only MultiWii controller.. And love them.
I have my own DiaLFonZo-Copter Shield and my new DiaLFonZo-Copter MiniControl (35x35 - 30.5mm hole mount)

Eric
info@dialfonzo-copter.com
RCG Plus Member
Old Sep 29, 2012, 08:24 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Just to let people know.
The boom clamp on the quad are my design and 3D printed at Shapeways.
Model HERE



I have made them so they have an aluminum standoff in the middle. I like that cause no messing with key or anything to hold the nut under while assembling.. very straitforward... It stay assembled even without the top plate ...

They have mountings at 25mm so any clamp you may find with that spacing would fit...
RCG Plus Member
Old Sep 29, 2012, 08:30 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Here is the top dimension with 225mm tube..
RCG Plus Member
Old Oct 02, 2012, 11:03 AM
Kipkool is offline
Find More Posts by Kipkool
Old Flying Bastard
Kipkool's Avatar
This looks really bad ass.
Hurry to see this fly

Nice job mate.

Let you a pm a week ago about your boom arms compatible with Dji frames.

Cheers.
Last edited by Kipkool; Oct 02, 2012 at 02:17 PM.
Old Oct 02, 2012, 11:55 AM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by Kipkool View Post
This looks really bad ass.
Hurry to this this fly

Nice job mate.

Let you a pm a week ago about your boom arms compatible with Dji frames.

Cheers.
Thanks
I did a little vibration plate.
Will post render of that later.
RCG Plus Member
Old Oct 02, 2012, 02:40 PM
Morphin is offline
Find More Posts by Morphin
Registered User
Quote:
Originally Posted by Dialfonzo View Post
Just to let people know.
The boom clamp on the quad are my design and 3D printed at Shapeways.
Model HERE



I have made them so they have an aluminum standoff in the middle. I like that cause no messing with key or anything to hold the nut under while assembling.. very straitforward... It stay assembled even without the top plate ...

They have mountings at 25mm so any clamp you may find with that spacing would fit...


How is the weight for the 16mm mount? (with/without aluminium standoff).
It is very interesting idea but i think it is too heavy...
Old Oct 02, 2012, 03:28 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by Morphin View Post




How is the weight for the 16mm mount? (with/without aluminium standoff).
It is very interesting idea but i think it is too heavy...
I didn't take the weight. But 3d print material is much lighter than plastic and standoff are 3/16 si very light too.

Would say they are equal or lighter than conventional clamp.

:-)
RCG Plus Member
Old Oct 02, 2012, 09:06 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Here is the modification for camera damping i did today..





Try to cut damper on the CNC
RCG Plus Member
Last edited by Dialfonzo; Oct 02, 2012 at 09:12 PM.
Old Oct 06, 2012, 09:36 PM
MTHead4u is offline
Find More Posts by MTHead4u
Having fun again!!
MTHead4u's Avatar
Looking great! I like the addition to the camera mount.

I'm ready whenever you are.
Old Oct 06, 2012, 09:57 PM
Dialfonzo is offline
Find More Posts by Dialfonzo
DiaLFonZo - UAV/Drone
Dialfonzo's Avatar
Quote:
Originally Posted by MTHead4u View Post
Looking great! I like the addition to the camera mount.

I'm ready whenever you are.
LOL..
Want to wait a little. ? I have someone who will extensively test the frame very soon..
RCG Plus Member


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion DiaLFonZo-Copter - DJI SpyderQuad Upgrade Dialfonzo Multirotor Talk 502 Aug 05, 2014 09:53 AM
New Product DiaLFonZo-Copter Boom Block Dialfonzo Multirotor Talk 88 Mar 21, 2014 06:34 AM
New Product DiaLFonZo-Copter - MicroTrinity Quad Dialfonzo Multirotor Talk 6 Jul 09, 2012 09:26 PM
Discussion FPV plate Soft mounted - Luis & DiaLFonZo-Copter Dialfonzo Multirotor Talk 5 Jan 05, 2012 01:04 PM