Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Sep 21, 2012, 09:59 AM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
That makes sense Odd - I was put onto him by Traplet as being 'their' wheel producer and asked him if he would make me a pair of 7" wheels. I gave him the section drawing but never heard back so I suspect he is either snowed under with work and could do without any more or has retired (semi?).
Sign up now
to remove ads between posts
Old Sep 21, 2012, 01:21 PM
alexkmmll is offline
Find More Posts by alexkmmll
I like to fly!
Too bad he doesn't seem to be around anymore... I'm not sure what to do about wheels if it comes down to it, I may just machine my own. The ply is 3/16" 5-ply, I think. Its for the wing
Spars, 2 fuselage formers, nacelles, and number 2 and 8 ribs. The rest of the inner-wing ribs and fuselage formers will be of 1/8" light ply, and the outer wings and tail surfaces will be balsa. I'll be cutting either tonight or tomorrow afternoon, depending on how fast I can do some templates tonight after work.

Have an awesome day, everyone!

Alex
Old Sep 21, 2012, 03:33 PM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
I am aware that 7" wheels are available - from at least half a dozen suppliers, but they are foam, which sounds good except that they are intended for much heavier models than we electric-power guys produce and are far too hard. Virtually no give at all. I reckon they'd survive being the wheel under a wheelbarrow-full of concrete.

Are you aware of Cyparis Alex? Similar weight to heavier grades of balsa but much stronger and more flexible making it about the most crash survivable material I know. I always use it for spars these days. The only drawback to it is that it doesn't like superglue.

Have fun cutting!
Old Sep 21, 2012, 08:34 PM
alexkmmll is offline
Find More Posts by alexkmmll
I like to fly!
Isn't the point you're not supposed to crash I'm not using any heavy load-bearing spars in the wings, so I don't have to really worry about using Cyparis on this build, though I may keep it in mind for the horizontal stab.

Tires with some give are pretty important for this model, too. I don't need to be sending my landing gear through my nacelles!

Alex
Old Sep 22, 2012, 02:47 AM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
I think there are two options for wheels - Kavan, which only go up to 5" IIRC and Dubro, which go to 6".

The Kavans are lighter and thinner walled but made of a harder rubber which is more plasticy. I have these on my Pe-2, but this is still not finished.

The Dubro 6" are 'proper' rubber with nice give but are about twice the wall thickness needed (even for the Stirling at 20 pounds AUW) and about twice as heavy, contributing about 1.5 of those 20 pounds. I do not put any additional air in them to keep them soft.

There used to be an eastern European make I was about to order a pair of - but they deleted the ones I wanted from the range just before I did.

CORRECTION:
I see the range on the last site mentioned is still there...
http://www.topmodelcz.cz/index.php?P...u_eshop_id=341
so it must have been that the Dubro 7" wheel disappeared - although by the time I found the Topmodel site the undercarriage was built and unable to accommodate the wider tyre of the 7" wheel.

Also there is still the RadioActive wheel available.
Last edited by eye4wings; Sep 22, 2012 at 04:37 AM.
Old Sep 22, 2012, 09:27 AM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
ODD, I may have got the wrong man! You called him Len Gardiner but when I looked up the man I had been put in touch with I see he is Vic Gardner.

There are a few requests for information on Len Gardiner on the LMA website and others which seem to suggest that he has retired from business, but nothing on Vic Gardner that I can see.

I have emailed Vic again in the rather forlorn hope of a response.
Old Oct 03, 2012, 03:54 PM
L.T. Pierce is offline
Find More Posts by L.T. Pierce
Registered User
Hello There:
I am in the middle of a MK-2 Beaufighter, interested in your build.
Have at thread at RCSB under scratch builds. You may be interested in
this book.

Regards Larry
Old Oct 29, 2012, 07:43 AM
Wilit run? 353 is offline
Find More Posts by Wilit run? 353
No such thing as overpowered
Wilit run? 353's Avatar
Nice build! If you need any inspiration here is John Ranson flying his Beaufighter.

JOHN RANSOME FLYING HIS SCALE EP BRISTOL BEAUFIGHTER RC PLANES AT HDMFC (4 min 26 sec)
Old Oct 29, 2012, 09:53 AM
audigex is offline
Find More Posts by audigex
Registered User
Apologies for the hijack, but do you have any more information on John Ranson's Beaufighter? Links etc? A PM would be great so as not to sidetrack this topic.
Old Oct 29, 2012, 12:41 PM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
There's information out there - just type John Ranson Beaufighter into your browser and you should find plenty... like this...
http://store.laser-design-services.c...products_id=61
Old Nov 01, 2012, 01:43 AM
rcgeorge29 is offline
Find More Posts by rcgeorge29
MAAC 79785
rcgeorge29's Avatar
Nice to see another Beaufighter on the go....I'm building the 104.5" version by Patrick Deslandes out of France.
Old Nov 01, 2012, 10:24 AM
Doug Bartley is offline
Find More Posts by Doug Bartley
Registered User
Doug Bartley's Avatar
7inchwheels are available from SDSHobbies according to their web page. I bought the same wheel in 5 inch, it is very light and robust with aluminum hub. Doug B
Old Nov 01, 2012, 10:38 AM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
Hi Doug,
Do you have a link to those 7" wheels please? SDSHobbies' search facility is most unselective... how can they think a prop spinner for example fits a search of 7" dia airwheel ?

Can you tell me if they are semi pneumatic or foam filled like all the others please?
It certainly looks right at 5"
Robin
Last edited by eye4wings; Nov 01, 2012 at 10:59 AM.
Old Nov 01, 2012, 07:51 PM
Doug Bartley is offline
Find More Posts by Doug Bartley
Registered User
Doug Bartley's Avatar
Hi eye4wings: Make sure you get to their home page. From there go to Airplane accessories, then wheels at bottom of the list. I'm sorry not literate enough with computer to do a"link", but above will get you there. Doug B
Old Nov 02, 2012, 04:58 AM
eye4wings is offline
Find More Posts by eye4wings
...design-build-fly-publish...
eye4wings's Avatar
Quote:
Originally Posted by Doug Bartley View Post
Hi eye4wings: Make sure you get to their home page. From there go to Airplane accessories, then wheels at bottom of the list. I'm sorry not literate enough with computer to do a"link", but above will get you there. Doug B
Thanks Doug.
Finally found the 7"wheels after three quarters of a frustrating hour ploughing through huge ranges of stuff I wasn't looking for (you'll gather I'm still not impressed with their search facility!). Must have taken a wrong turn somewhere...
http://www.sdshobby.net/7inch-pu-whe...l#.UJOGBGdmwhQ

Having a laugh aren't they?
The price seems to suggest a huge hike for rarity value... $67 ? And that doesn't even appear to be for a pair.
My assessment - SDSHobby = Rip-off specialists.

Or maybe the days of China = Cheap are gone already?
Ah well.... take a deep breath and get on with things...


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
FYI Bristol Beaufighter on sale JCastle Scale Kit/Scratch Built 67 May 19, 2005 09:27 AM
For Sale-Hobby-Lobby Bristol Beaufighter "Save 40 Bucks" Joe Pierson Aircraft - Electric - Airplanes (FS/W) 4 Jun 25, 2002 10:59 AM
FS--Twin BRISTOL BEAUFIGHTER on EBAY speedo Aircraft - Electric - Airplanes (FS/W) 2 May 30, 2002 06:51 PM
Bristol Beaufighter or DC3-Dakota Patrick Plawner Scale Kit/Scratch Built 3 Jan 27, 2002 04:22 PM
Anyone have the Bristol Beaufighter from HL Glenn Samonte Scale Kit/Scratch Built 9 Jan 08, 2002 12:47 PM