New Products Flash Sale
Thread Tools
Old Dec 26, 2012, 12:12 AM
jtaylor996 is offline
Find More Posts by jtaylor996
Registered Crasher
According to servo database the specs for torque and speed should be the same for the HS-65mg @ 6v and the MG14 @ 4.8v.

My servo tester can't verify this. Does this seem right to anyone that has used both servos, or is the MG14 spec optimistic?
Sign up now
to remove ads between posts
Old Dec 26, 2012, 12:44 AM
uptime4downtime is offline
Find More Posts by uptime4downtime
3d Kiwi
uptime4downtime's Avatar
I just looked at the roll rate on SD's video, and it is superior to my MG14's on 4.8v, but I have yet to test MG14 on 6v, until my BEC arrives. I don't enjoy killing 65mg's simply due to cost, and when an MG14 goes it is less 'painful' in that respect. I actually have not killed an MG14 yet, only 65mg's. My thinking is that if you have the Hitec, then by all accounts it is a solid reliable servo, so run with that. Others may have other opinions to share, as I have no experience on 6v as of yet
Old Dec 26, 2012, 08:05 AM
jetinteriorguy is offline
Find More Posts by jetinteriorguy
Registered User
I have use the TP Mg14's on 6v in a couple of planes and they have performed very well for me. Strong, center well and very reliable. They aren't real fast but are ok.
Old Dec 26, 2012, 09:58 AM
JDMCARPETS is offline
Find More Posts by JDMCARPETS
KING of PING!
JDMCARPETS's Avatar
Put plane on ground with WOT and up elevator.If elevator blows down you need bigger servo,smaller prop or different configuration on control arms.....
Old Dec 26, 2012, 10:51 AM
PlaneButcher is offline
Find More Posts by PlaneButcher
Registered User
I don't think that puts the same loads on the servo as high speed knife edge spins, snaps, pop tops, etc.
Old Dec 26, 2012, 11:17 AM
JDMCARPETS is offline
Find More Posts by JDMCARPETS
KING of PING!
JDMCARPETS's Avatar
are you doing those maneuvers at WOT ? and full elevator
Last edited by JDMCARPETS; Dec 26, 2012 at 12:57 PM.
Old Dec 26, 2012, 11:50 AM
PlaneButcher is offline
Find More Posts by PlaneButcher
Registered User
Quote:
Originally Posted by JDMCARPETS View Post
are you doing those maneuvers at WOT ?
Yes
Old Dec 26, 2012, 11:57 AM
JDMCARPETS is offline
Find More Posts by JDMCARPETS
KING of PING!
JDMCARPETS's Avatar
Then your not doing a pop top
Old Dec 26, 2012, 12:28 PM
PlaneButcher is offline
Find More Posts by PlaneButcher
Registered User
WOT entry.
Old Dec 26, 2012, 12:43 PM
JDMCARPETS is offline
Find More Posts by JDMCARPETS
KING of PING!
JDMCARPETS's Avatar
Merry Christmas
Old Dec 26, 2012, 01:19 PM
PlaneButcher is offline
Find More Posts by PlaneButcher
Registered User
Oh crap!!! I celebrated Christmas one day early.
Old Dec 26, 2012, 01:40 PM
JDMCARPETS is offline
Find More Posts by JDMCARPETS
KING of PING!
JDMCARPETS's Avatar
you also didn't pull full elevator on entry
Old Dec 26, 2012, 01:42 PM
PlaneButcher is offline
Find More Posts by PlaneButcher
Registered User
I hate when that happens! At least I was WOT. LOL
Old Dec 26, 2012, 01:45 PM
uptime4downtime is offline
Find More Posts by uptime4downtime
3d Kiwi
uptime4downtime's Avatar
Quote:
Originally Posted by jtaylor996 View Post
According to servo database the specs for torque and speed should be the same for the HS-65mg @ 6v and the MG14 @ 4.8v.

My servo tester can't verify this. Does this seem right to anyone that has used both servos, or is the MG14 spec optimistic?
Oh, just noticed those were 65 hb you have, I think you really need mg on this plane.
Old Dec 26, 2012, 04:59 PM
jtaylor996 is offline
Find More Posts by jtaylor996
Registered Crasher
I was thinking of using HB on AIL, and then pulling the MG for the tail from another plane.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Skywing, Winner's Model, Hokusei, 3DHS 48"-55" EPP Build & Repair Tips groovejet 3D Foamies 459 Apr 30, 2016 12:31 PM
New Product SkyWing 39-in EPP Edge-540 feda 3D Foamies 120 Jan 22, 2014 07:01 PM
Discussion SkyWing 48-in Extra 300L Under Development feda 3D Foamies 229 Nov 04, 2012 02:55 AM
Sold 3DHS 48" Orange Edge 540 LPU in CT newheliguy81 Aircraft - Electric - Airplanes (FS/W) 2 Aug 19, 2012 08:57 AM