Shop our Airplanes Products Drone Products Sales
Thread Tools
Old Sep 06, 2012, 12:49 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I'm a little skeptical of the HK gearboxes though. The one I got a while back was a mess. I'll stick with the J3 motor that's been proven in so many cases.
BSD and Homefly have the gears as well as a few other places.
There is plenty of room for more micros.

I'll be getting and RX41d and a MicroAct for the rudder. I doubt it will have the authority I want, but oh well. I have to make a sacrifice.


Oh and this is being built for our fly-in on the 4th of November so I have a while to go.
Sign up now
to remove ads between posts
Old Sep 06, 2012, 06:21 PM
nemoskull is offline
Find More Posts by nemoskull
Pilot, Co-pilot, Navagator
nemoskull's Avatar
no, the HK GB suck, but ive had a hard time finding a 6MM motor that was lower than 4.5 ohm for sale...
Old Sep 06, 2012, 06:23 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Our group might be placing an HK order soon so I'll be sure to throw one in the cart.
Old Sep 06, 2012, 06:49 PM
nemoskull is offline
Find More Posts by nemoskull
Pilot, Co-pilot, Navagator
nemoskull's Avatar
they should have just the motor....

http://www.hobbyking.com/hobbyking/s...dproduct=21170
Old Sep 07, 2012, 02:06 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Is it ok for me to use the Mylar for the hinge, or is that a bad idea? My bigger Isis had all of the hinges on the bottom, but the top would be more aesthetically pleasing. I'm just not sure if the 2um would peel or rip.
Old Sep 07, 2012, 02:09 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
Another option would be to put a tape hinge then apply the skin. Ya that's what I'll do. I just need some clear tape now.
Old Sep 07, 2012, 02:45 PM
nemoskull is offline
Find More Posts by nemoskull
Pilot, Co-pilot, Navagator
nemoskull's Avatar
i alway hing top, theroy is to nt disturb the upper faster moving airfoil.
Old Sep 11, 2012, 05:48 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
The covering arrived today, but there was no slip in my box so I did not know. I'll go and get it tomorrow. I'll have this this covered and assembled (for the most part) this weekend.
Old Sep 13, 2012, 12:43 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I got the shipping labels mixed up, and D Lewis is getting back from vacation so it will hopefully get shipped out soon.
Old Sep 18, 2012, 01:05 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I ordered the receiver, actuator, motor, prop adapter, and gearbox gears.

Rx41d
MicroAct
HK GPS-6 6mm motor
9t pinion
36t Spur

I think that's everything, but the battery.
Old Sep 22, 2012, 01:13 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I just need one of the curved exacto blades to cut the mylar.

Name: ImageUploadedByTapatalk1348290595.072808.jpg
Views: 81
Size: 161.5 KB
Description:
Old Sep 24, 2012, 01:24 PM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
I received the rx and actuator today along with the prop saver. I should be getting the gearbox housing later today after class. At first I wanted to put connectors on the rx, but I think I will just solder everything, but the act, directly to the board.
Old Oct 03, 2012, 11:08 AM
boredom.is.me is offline
Find More Posts by boredom.is.me
Micro Boat Forum Founder
boredom.is.me's Avatar
The procrastination here is killing me...

The plane is already built. I just need to solder and install everything. I guess I'll get to that on Friday.
Old Oct 03, 2012, 12:12 PM
indoor_fr is online now
Find More Posts by indoor_fr
Registered User
indoor_fr's Avatar
Quote:
Originally Posted by boredom.is.me View Post
The procrastination here is killing me...

The plane is already built. I just need to solder and install everything. I guess I'll get to that on Friday.

I know what you are talking about! I have an extra 300 S made at 80%, that is waiting for months to be finished...

Keep on the good work.
Old Oct 04, 2012, 01:14 PM
nemoskull is offline
Find More Posts by nemoskull
Pilot, Co-pilot, Navagator
nemoskull's Avatar
try to avoid solderin the rx if you can... its a bad idea to do so. (ask me how i know )


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Build Log Isis 3: A Custom DLG Project Keenan smith Hand Launch 20 Feb 10, 2013 06:45 PM
New Product Isis II Keenan smith Hand Launch 96 Jul 11, 2012 12:36 PM
Build Log Isis G2: Ultralight 3D boredom.is.me Scratchbuilt Indoor and Micro Models 14 Apr 05, 2012 01:23 AM
Build Log Isis - the Lico Look Alike: Maiden Success! boredom.is.me Scratchbuilt Indoor and Micro Models 140 Jan 15, 2012 05:57 AM