New Products Flash Sale
Thread Tools
Old Oct 09, 2012, 09:58 PM
indoorheli is offline
Find More Posts by indoorheli
2 seconds from crashing
indoorheli's Avatar
Quote:
Originally Posted by nebwake View Post
I cannot get the vibrations out of the heli. I have tried both sets of blades, adjusted the blade grip tightness from loose to tight, made sure the feathering shaft was tight. what else are you guys doing to fix vibration? is it necessary to balance these little blades?
yes balance them
Also check your feathering shaft to verify it isnt bent. You want the feathering shaft tight but not too tight. Tighten until the blade grips start to bind then back off until they move freely
Sign up now
to remove ads between posts
Old Oct 09, 2012, 10:03 PM
J_skaggs is offline
Find More Posts by J_skaggs
Registered User
Quote:
Originally Posted by nebwake View Post
I cannot get the vibrations out of the heli. I have tried both sets of blades, adjusted the blade grip tightness from loose to tight, made sure the feathering shaft was tight. what else are you guys doing to fix vibration? is it necessary to balance these little blades?
Feathering shaft should have a hairs worth of end play not tight. I had vibration and tried everything but, nothing helped. I changed the motor because, it seemed to be pulsing and that fixed it. Now it is very smooth flying.
Old Oct 09, 2012, 10:04 PM
dway is offline
Find More Posts by dway
Registered User
Quote:
Originally Posted by nebwake View Post
I cannot get the vibrations out of the heli. I have tried both sets of blades, adjusted the blade grip tightness from loose to tight, made sure the feathering shaft was tight. what else are you guys doing to fix vibration? is it necessary to balance these little blades?
Try loosening it up a little. Horizon says that there should be about a hair width of play.
Old Oct 09, 2012, 10:11 PM
nebwake is offline
Find More Posts by nebwake
Registered User
nebwake's Avatar
cool, ill try that, thanks!
Old Oct 10, 2012, 12:28 AM
micro50 is offline
Find More Posts by micro50
Registered User
Is a good mod, not like brushless but beter than stock. take a drill and glue sand paper to half of it. Only sand the front side of the frame. remember you need a 10t Pinion to make this work or you wil not see 5500 heed speed Zero pitch, full pitch 3400 MQX Clockwize Motor.
Old Oct 10, 2012, 12:53 AM
E1Allen is offline
Find More Posts by E1Allen
UH60 Pilot
E1Allen's Avatar
I got some crazy vibrations when I bent the feathering spindle. Bent it back and all is well. Awesome little helicopter. I also found out those little black plastic pieces are for the feathering spindle, only after I somehow removed and installed with the point of a razor blade and a screw driver. My nano tech batteries are not performing more than 3 minutes in fff, it dies when I try to go IU. Stock batteries work just fine though.
Old Oct 10, 2012, 08:17 AM
sbarro is online now
Find More Posts by sbarro
Registered User
Quote:
Originally Posted by indoorheli View Post
yes balance them
Also check your feathering shaft to verify it isnt bent. You want the feathering shaft tight but not too tight. Tighten until the blade grips start to bind then back off until they move freely
If you are still getting vibes after this, pull off the head and run up the heli to check for a bent main shaft. Mine came out of the box with a slight bend, enough to cause vibrations.
Easy fix to make another shaft- 2mm cf rod, using the old main shaft as a template
Old Oct 10, 2012, 08:17 AM
micro50 is offline
Find More Posts by micro50
Registered User
What is the heed speed of a ncpx ?
Old Oct 10, 2012, 08:48 AM
chulian1819 is offline
Find More Posts by chulian1819
Registered User
chulian1819's Avatar
Guys where do you buy the brushless conversions with international shipping? and for mcpx?

thank you in advance!
Old Oct 10, 2012, 09:43 AM
JLink125 is offline
Find More Posts by JLink125
Registered User
JLink125's Avatar
Quote:
Originally Posted by micro50 View Post
Is a good mod, not like brushless but beter than stock. take a drill and glue sand paper to half of it. Only sand the front side of the frame. remember you need a 10t Pinion to make this work or you wil not see 5500 heed speed Zero pitch, full pitch 3400 MQX Clockwize Motor.
I'm picking up one of these motors today, I will do the BL upgrade as soon as they are available but this looks good for now since my stock motor is toast. I took it apart since I will be replacing it anyway and found a lot of fine metal specks in and around the end of the motor around the brushes, looks like these little motors are eating themselves alive. Wish HH would use better quality motors, it's a bit disappointing to have it die with only 40 or so flights and only 20 to 25 of them were at full performance before I lost quite a bit of power. Where can I get a 10t pinion? Any pics of the mod would be really helpful.
Old Oct 10, 2012, 10:41 AM
brushless55 is offline
Find More Posts by brushless55
big ignore list
brushless55's Avatar
cool little heli..
just flew my fourth pack through it..
feels like it needs a tad more power with my DX6i
Old Oct 10, 2012, 11:01 AM
indoorheli is offline
Find More Posts by indoorheli
2 seconds from crashing
indoorheli's Avatar
Quote:
Originally Posted by chulian1819 View Post
Guys where do you buy the brushless conversions with international shipping? and for mcpx?

thank you in advance!
Well as far as a kit there is none available yet. But you can buy all the parts from Dylan at astroiddesigns.com or Topper at topcopter.com.

If you want a kit Dylan should have some in a few weeks.
Old Oct 10, 2012, 02:12 PM
Willyboy is offline
Find More Posts by Willyboy
Registered User
Willyboy's Avatar
Just curious, has anyone tried the MSRX coreless motor (BLH 3203) motor in the Nano and if so, how do you like it?

Bob
Old Oct 10, 2012, 02:26 PM
indoorheli is offline
Find More Posts by indoorheli
2 seconds from crashing
indoorheli's Avatar
I almost did But I stole the 8t pinion off of it instead
Old Oct 10, 2012, 02:32 PM
Daryoon is online now
Find More Posts by Daryoon
Team WarpSquad
Daryoon's Avatar
I believe the mSRX coreless motor is 8.5mm. While the nCPX is 8mm. So you'll probably have to sand and mod the mount like the guy above suggested for the mQX motor. Which I am still having a difficult time understanding BTW.

It sounds like you gotta sand the mount to fit the 8.5mm motor. Then gotta use a 10tooth pinion to reach the main gear. While adding weight to the nCPX?

Sounds like getting a brushless on there is still better.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Cool Walkera MiNi CP - Smallest 100 sized 3D helicopter zadaw Micro Helis 6166 Nov 20, 2016 12:57 AM
Discussion is there anything better than mcpx v2 at same or smaller size? Legendary_Agent 3D Electric Heli Flying 33 Feb 24, 2012 09:46 PM
Question Whatís Better than a Blade CP and Smaller than a Trex? HavingFun2002 Micro Helis 74 Mar 05, 2006 06:07 PM