Thread Tools
Sep 24, 2012, 12:18 PM
2 Turbos...Nope 1 Big one
skeppley's Avatar
I had to order from ebay.
The Hobbytown near me didnt even know what the nano cpx was!!! REALLY???
Sign up now
to remove ads between posts
Sep 24, 2012, 12:21 PM
2 seconds from crashing
indoorheli's Avatar
hobbytown near me is horrible Though I hear they will have the nano at the end of October
Sep 24, 2012, 12:56 PM
Gone Huckin'
turnerm's Avatar
Quote:
Originally Posted by skeppley
I had to order from ebay.
The Hobbytown near me didnt even know what the nano cpx was!!! REALLY???
I got the same thing when I called around. They were like "nano what?"
Sep 24, 2012, 01:22 PM
Registered User
Willyboy's Avatar
Okay, I live in the boonies and I am going into town (50 miles away) to he big city of Bakersfield, Ca on Thursday. Just called the LHS there and he has four Nano CPxs' in stock. Should I or shouldn't I.

Bob
Sep 24, 2012, 01:28 PM
Registered User
You should.
Sep 24, 2012, 01:30 PM
Luck is my skill
queadlunnrau's Avatar
Really ur thinking about it rather than driving there now?
Sep 24, 2012, 01:42 PM
Registered User
Willyboy's Avatar
Quote:
Originally Posted by queadlunnrau
Really ur thinking about it rather than driving there now?
Okay, Okay, I just told the wife that we are going tomorrow. Lord this has been killing me since I have been reading all these threads on this bird. I did eight flights on my 130X this morning and now the wind is blowing about 35-40 miles an hour but not inside the house where I can really use the Nano.

Bob
Sep 24, 2012, 01:46 PM
Registered User
BigGuyJT's Avatar
Quote:
Originally Posted by Willyboy
Okay, I live in the boonies and I am going into town (50 miles away) to he big city of Bakersfield, Ca on Thursday. Just called the LHS there and he has four Nano CPxs' in stock. Should I or shouldn't I.

Bob
Got some here in fresno if he runs out by the time you there!
Sep 24, 2012, 01:52 PM
Registered User
Willyboy's Avatar
Quote:
Originally Posted by BigGuyJT
Got some here in fresno if he runs out by the time you there!
Thanks, I will keep that in mine if they don't have any tomorrow. But I think he will because most flyer there are plank flyers.

Bob
Sep 24, 2012, 02:25 PM
RC Helis: My Healthy Obsession
Quote:
Originally Posted by M3_matt
Funny! Mine has been holding up well, but I broke the rear swash ball! Used some Gorillia glue and it seems to be holding up. It sucks there aren't a surplus of parts yet for this baby!! Oh and also one of my batteries has taken a dump!
I would strongly suggest you don't use the stock charger. It is putting out twice the amps needed to charge these little packs. If you want your batteries to last as long as possible, use the old MCPx charger (minus the middle connector) at .1a. My packs are as good as they were new after more than 20 cycles so far.
Sep 24, 2012, 02:28 PM
Registered User
M3_matt's Avatar
Double post!!
Last edited by M3_matt; Sep 24, 2012 at 02:33 PM.
Sep 24, 2012, 02:30 PM
Team WarpSquad
Daryoon's Avatar
The HobbyTown in San Marcos, (northern San Diego) had it last Friday. The guy said the shipment just came in so he hasn't had a chance to put it out. Ampdraw in San Diego said all the BNF are going to people who preordered. Discount Hobby in San Diego has a number of them on the shelf. I walked in and grabbed one yesterday. Just put a few batteries through her this morning. My first CP. Only owned mainly clone FP helis that I've modded and more recently, the v929.

Flies nice. Dialed in -10 expo for indoors. I like it sensitive. Helps to keep her off the funitures and walls. At the +30 expo the manual suggested, it was too loose and slow to react.

About to put another set through her now.
Sep 24, 2012, 02:32 PM
2 seconds from crashing
indoorheli's Avatar
Quote:
Originally Posted by M3_matt
Yep! Thanks! I have been using the Celectra 4 port, and it seems to be taking a toll on my batteries!!
~TIME WARP~
you can adjust the output on the 4 port celectra chargers

Open up the charger and turn the pot for each port down two notches

I havent opened up the single chargers used by blade but i bet they have an adjustment pot as well.
Sep 24, 2012, 02:32 PM
Registered User
M3_matt's Avatar
Quote:
Originally Posted by dkfuji
I would strongly suggest you don't use the stock charger. It is putting out twice the amps needed to charge these little packs. If you want your batteries to last as long as possible, use the old MCPx charger (minus the middle connector) at .1a. My packs are as good as they were new after more than 20 cycles so far.
Yep! Thanks! I have been using the Celectra 4 port, and it seems to be taking a toll on my batteries!!
Sep 24, 2012, 02:48 PM
Registered User
300mA charge rate is fine for the included batteries, which list a 3C charge rate (450mA). I've been charging EFlite 150mAh and TP 160mAh 25C batteries at 300mAh and have not had any problems with shortened life.

Now, with the old 12/14C EFlite batteries, 300mAh was too much and did shorten their life (not that they were worth using when new).


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Cool Walkera MiNi CP - Smallest 100 sized 3D helicopter zadaw Micro Helis 6166 Nov 19, 2016 11:57 PM
Discussion is there anything better than mcpx v2 at same or smaller size? Legendary_Agent 3D Electric Heli Flying 33 Feb 24, 2012 08:46 PM
Question Whatís Better than a Blade CP and Smaller than a Trex? HavingFun2002 Micro Helis 74 Mar 05, 2006 05:07 PM