Thread Tools
Old Oct 09, 2012, 03:44 PM
brontide is offline
Find More Posts by brontide
Stop me before I build again!
A little over 3 minutes on take 2 before one of the motor mounts failed and the unit crashed down. Thankfully I should be able to work off the wood and re-epoxy a new arm tonight. Needless to say I'm not amused.

The problem with wood, as I'm finding is that it's also very hard to get good, straight squares, so it has a rotational issue that it hard to pin down.

Grrrr
Sign up now
to remove ads between posts
Old Oct 09, 2012, 05:54 PM
MrKim is offline
Find More Posts by MrKim
Registered User
MrKim's Avatar

X-Copter Two


Hi again!

A week ago i made a new and smaller quadcopter here are some Pics. Vids. & Specs.







X-Copter Two @ Airfield Maarke-Kerkem (3 min 30 sec)


X-Copter Two NightFlight (08-10-2012) (3 min 40 sec)


-Specs-
Motors: Turnigy 2204-14T 19g Outrunner
ESC: Turnigy 12amp Plush
Props: 8x4,5
Frame: Wood DIY
Batt: Turnigy 1300mah 3S 35C(To low only 4min flight time!)
Board: KK V2 LCD Board & Kaptein Kuk Firmware Update V1.2
Turnigy Receiver Controlled Switch & High Density Waterproof Flexible LED Strip

Question? Feel free to ask!

Kim D.
Old Oct 09, 2012, 06:50 PM
carr52 is offline
Find More Posts by carr52
Registered User
carr52's Avatar
I am preparing to build my first quad copter. Just wanted say thanks to all the folks that have helped along the way. Thanks.

Tom
Old Oct 09, 2012, 07:34 PM
2400RDR is online now
Find More Posts by 2400RDR
Out of helis, sanity returning
Quote:
Originally Posted by MrKim View Post
Hi again!

A week ago i made a new and smaller quadcopter here are some Pics. Vids. & Specs.

Kim D.
Sweet! I love wood frames.
Old Oct 10, 2012, 02:51 AM
Captain3D is offline
Find More Posts by Captain3D
------------------------
Captain3D's Avatar
Quote:
Originally Posted by brontide View Post
Do they sell it without a seam, or did you glue it together yourself?
It has a glue seal already to be pressed together. Just peel off the cover and it sticks great. Actually I bought this on in OSH hardware.

phil
Old Oct 10, 2012, 06:12 AM
brontide is offline
Find More Posts by brontide
Stop me before I build again!
Third time's a charm?

Didn't like the lack of stiffness and straightness in the wooden frame so I fabricated a replacement frame for the electronics and did a transplant last night. One boom is wood in order to keep the weight down as one alu boom was more than stiff to prevent any edge to edge torsion all by itself. Whole thing is held together by 4 bolts and lots of zip ties.
Old Oct 10, 2012, 08:14 AM
carr52 is offline
Find More Posts by carr52
Registered User
carr52's Avatar
This is my list of parts I think I'll need except I'll be going with a 30 or 40 amp esc. I have my own Tx and Rx and battery. Did I forget anything?

Tom

Motor: http://www.hobbyking.com/hobbyking/s...ess_Motor.html
ESC: http://www.hobbyking.com/hobbyking/s..._ESC_2_4S.html
KK2 Board:
http://www.hobbyking.com/hobbyking/s...trol_Board.htm
Power board: http://www.hobbyking.com/hobbyking/s...ion_Board.html
Plugs : http://www.hobbyking.com/hobbyking/s...0pcs_set_.html

Oh yeah and I too like wooden frames. Thanks for the pics.
Old Oct 10, 2012, 08:31 AM
brontide is offline
Find More Posts by brontide
Stop me before I build again!
Tom, the links are broken.

Some things off the top of my head looking at my quad.

Does the motor come with a good mount for props, maybe get a "prop saver" for your shaft size.
Wires. Do you have appropriate gauge wire and heat shrink
Servo extensions. You have to plug something from the Rx to the KK2
Screws, bolts, standoffs, locknuts? Cheap from HK and the small metric stuff can be a bear to find in the US.
You probably have bullets, get more than you need.
Battery plug pairs. As always, get spares.

Of course I presume you already have batteries or can source them from a US vendor.

EDIT: Also, props?
Last edited by brontide; Oct 10, 2012 at 08:39 AM.
Old Oct 10, 2012, 08:40 AM
carr52 is offline
Find More Posts by carr52
Registered User
carr52's Avatar
http://www.hobbyking.com/hobbyking/s...ustomer=667550

This is suppose to be a link to my HK wish list.
Old Oct 10, 2012, 08:41 AM
brontide is offline
Find More Posts by brontide
Stop me before I build again!
Quote:
Originally Posted by carr52 View Post
http://www.hobbyking.com/hobbyking/s...ustomer=667550

This is suppose to be a link to my HK wish list.
No good, sites says no items in the list. :-)
Old Oct 10, 2012, 09:27 AM
carr52 is offline
Find More Posts by carr52
Registered User
carr52's Avatar
Do these links work on your end?
Old Oct 10, 2012, 09:30 AM
brontide is offline
Find More Posts by brontide
Stop me before I build again!
Quote:
Originally Posted by carr52 View Post
Do these links work on your end?
Yes, these do.
Old Oct 10, 2012, 09:38 AM
carr52 is offline
Find More Posts by carr52
Registered User
carr52's Avatar
I'm planning on making my frame using carbon fiber tube, plexiglass and aluminum. I'll try re-inserting the links for the motor and KK2. Board and other bits I'll be using.
Motor
http://www.hobbyking.com/hobbyking/s...dProduct=12920
Flight control board
http://www.hobbyking.com/hobbyking/s...dProduct=24723
Esc
http://www.hobbyking.com/hobbyking/s...dProduct=25365
Power board
http://www.hobbyking.com/hobbyking/s...dProduct=23140
Old Oct 10, 2012, 10:52 AM
highviz is online now
Find More Posts by highviz
Registered User
Quote:
Originally Posted by carr52 View Post
I'm planning on making my frame using carbon fiber tube, plexiglass and aluminum. I'll try re-inserting the links for the motor and KK2. Board and other bits I'll be using.
Motor
http://www.hobbyking.com/hobbyking/s...dProduct=12920
Flight control board
http://www.hobbyking.com/hobbyking/s...dProduct=24723
Esc
http://www.hobbyking.com/hobbyking/s...dProduct=25365
Power board
http://www.hobbyking.com/hobbyking/s...dProduct=23140
Mmm- personally I would not use plexiglass (acrylic plastic) as it is very brittle and will not take kindly to any impact - If you want a clear plastic go for polycarbonate as it is much tougher. Otherwise use a reinforced plastic (grp etc) to get strength with lower weight.

Again only my observation, but the 1400Kv motor you list might not be ideal - you will have to run pretty small props to keep the amps down with that sort of rpm/volt. On a lightweight quad I'll go up to 1200Kv, but for most applications I tend to use 750 - 900Kv motors.

- Just my thoughts, but don't let my comments stop you experimenting ........

Malcolm


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Show us your RC orders! Lets see how much we spend :O Koo Electric Plane Talk 60 Nov 25, 2016 12:32 AM
Discussion Show Us your US Navy Ship ! Chophop Life, The Universe, and Politics 92 Jul 16, 2016 05:49 PM
Discussion Show us your favorite hi-res FPV video compuatic FPV Talk 10 Jan 04, 2015 02:38 AM
Discussion Show us your workshop bazman The Builders Workshop 41 Jul 21, 2014 11:16 PM
Discussion Show Us Your Hoverthings FPV Frame scrape Multirotor Talk 2149 Apr 18, 2014 06:06 PM