Thread Tools
Jul 24, 2012, 07:28 AM
LiPo-Sucker & Airframe EMT
pugsam's Avatar
Quote:
Originally Posted by AirHermit View Post
On it!
Do you buy Welders by the case?

Sign up now
to remove ads between posts
Jul 24, 2012, 07:37 AM
Limb stalker
Parksinatree's Avatar
Gonna need all that Welder's for assembly? Dang, guess I need to get more....
Jul 24, 2012, 08:30 AM
3D Hack
JC Spohr's Avatar
10 tubes of Welder's.

I was thinking 2 tubes would get the job done!

JC
Jul 24, 2012, 08:50 AM
Team Twisted!
cdee's Avatar
Great pictures... first ones out from the general public... nice!! Tracking says I should have mine tomorrow... so in the mean time, as mentioned, I just have to drool over what is starting to arrive for others...

Got everything coming from Twisted Hobbys that was needed, with the exception of the motor, picked one of those up at the LHS yesterday, will use a spektrum Rx on this plane, got one of those available in my stash... so at this point all set and ready. Looking forward to the Build posts.
.
cdee
.
Jul 24, 2012, 09:40 AM
Addicted
The servo arm extensions are included with the airframe, correct?
Jul 24, 2012, 10:07 AM
Don't give in to gravity
Gravitycheat's Avatar
Quote:
Originally Posted by Sixinarow View Post
The servo arm extensions are included with the airframe, correct?
That is correct.
Jul 24, 2012, 10:13 AM
Team Twisted!
cdee's Avatar
Quote:
Originally Posted by Gravitycheat View Post
That is correct.
pull-pull on the rudder... push rod on the elevator??
.
cdee
.
Jul 24, 2012, 10:23 AM
Don't give in to gravity
Gravitycheat's Avatar
Quote:
Originally Posted by cdee View Post
pull-pull on the rudder... push rod on the elevator??
.
cdee
.
That is correct as well.
Jul 24, 2012, 10:23 AM
3D Hack
JC Spohr's Avatar
Quote:
Originally Posted by cdee View Post
pull-pull on the rudder... push rod on the elevator??
.
cdee
.
Correct - according to the instruction manual.

But, not sure if EZ connectors are included. Manual talks about making z-bends.

JC
Jul 24, 2012, 10:29 AM
3D Hack
JC Spohr's Avatar
My plane is "On Vehicle for Delivery Today - Out For Delivery"

Gravity, anyone else same status?

Trying to make sure I have everything to complete build quickly.

So far, I think I need some EZ connectors and a spinner (~35mm).

Anything else anyone can think of that that not included in kit (excluding power combo or glue)?

JC
Jul 24, 2012, 10:35 AM
Team Twisted!
cdee's Avatar
Mine still shows by the "end of day 7/25"
.
cdee
.
Jul 24, 2012, 11:31 AM
Fly Low!!!! No Sked.
AirHermit's Avatar
Quote:
Originally Posted by pugsam View Post
Do you buy Welders by the case?

Quote:
Originally Posted by Parksinatree View Post
Gonna need all that Welder's for assembly? Dang, guess I need to get more....
Quote:
Originally Posted by JC Spohr View Post
10 tubes of Welder's.

I was thinking 2 tubes would get the job done!

JC
I thought you guys would enjoy that shot of the Welders. It was on Sale here, Two tubes for $4 and thats good for were I live so I kinda made sure I had enough. And Acctually Im up to my third tube Of welders at the moment.
Jul 24, 2012, 11:47 AM
Addicted
Lowes has 2-packs for $4. I'll go grab a few
Jul 24, 2012, 12:03 PM
Fly Low!!!! No Sked.
AirHermit's Avatar

...All nighter.....or Atleast till 1:30...


I could not resist but to start the build allready. Especially when I found out I was given the day off from work and, I did not need to install servo's between the frames. Just a few quick pictures, no real Detaled shots but at leasts its ready for Electronics when It gets here or when I can get back to this build. Work is gonna keep me busy till after the weekend so this is as far Ill go till then.

Enjoy! Thanks again to Twisted and ALL that are involved.

Build started about 8:30Pm






Tail section not intalled yet, and wont glue into place yet till i see how fellow Sbach builders do with the Push-Pull string thingie
At this point, thats my third tube of welders sitting under the plane.
The Landing Gear seems pretty durable and looks great IMO.


1:30AM Sbach AirFrame finding a spot with its other 'Twisted' siblings


Jul 24, 2012, 12:12 PM
Team Twisted!
cdee's Avatar
NICE....!!!

The big size is great... nice to see the comparisons next to all your other Twisted products. Quite a bit bigger than the Extra Slick.... Impressive. I was hesitant too on the pull-pull on the 1.0m sbach, but forced myself through it, and am glad I did, I ended up really liking it.
.
cdee
.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Twisted Hobbys - RC Factory USA Sbach 342 39" Build Thread & Flight Video!!!!! aerofundan 3D Foamies 497 May 24, 2015 08:01 AM
Discussion Twisted Hobbys - RC Factory USA YAK-55 39" Build Thread/Videos & Flight Video!!!!! cbriggs11 3D Foamies 78 May 28, 2014 05:40 PM
Discussion NEW Twisted Hobbys/ParkAero RC Factory 31" Sbach 342 Greengiant 3D Foamies 130 Jan 24, 2013 01:49 PM
Discussion NEW RC Factory-Park Aero/Twisted Hobbys 31" Sbach 342 Greengiant 3D Flying 0 Nov 04, 2011 11:34 AM
Discussion RC Factory USA - Twisted Hobbys - 1.2m SU 29 Build Thread. hercdriver7777 3D Foamies 97 Oct 19, 2011 06:34 AM