3D Hobby Shop 40" Edge 540 Epp Full Fuse - Page 98 - RC Groups
Thread Tools
Aug 29, 2012, 09:43 AM
fly and then fly some more!
nickelbn1's Avatar
http://www.hobbyking.com/hobbyking/s...ner_Motor.html

This one maybe? Close to the omega 103g
Sign up now
to remove ads between posts
Aug 29, 2012, 10:15 AM
Registered User
dentalpain's Avatar
I wish this was a two piece removable wing. I bet the chances of thie twist, warp would be greatly diminshed during production. It would also be super easy to transport.
Aug 29, 2012, 10:21 AM
Registered User
That's what I was confused about I couldn't find the motor I have on hobby king, the one you linked is a D3530 1250kv and the one I have is a C3530 1100kv.
Aug 29, 2012, 10:37 AM
Team Aztech Aeromodels!
zmonster97's Avatar
Quote:
Originally Posted by 3DHSISEPICS
That's what I was confused about I couldn't find the motor I have on hobby king, the one you linked is a D3530 1250kv and the one I have is a C3530 1100kv.
This motor is pretty darn close to the omega 72g.

http://www.hobbyking.com/hobbyking/s...dProduct=18160

And I think the motor you have(C3530) is discontinued because I can't seem to find just the orange/yellow turnigy motors anymore. I think they have been replaced with this line.

http://www.hobbyking.com/hobbyking/s...URNIGY_XP.html

Another close match to the 72g omega.

http://www.hobbyking.com/hobbyking/s...ner_Motor.html


All of these motors seem to have less power than the omega however.
Aug 29, 2012, 10:55 AM
"Get off the runway!"
Da Big_G's Avatar
According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...
Aug 29, 2012, 11:12 AM
Registered User
Quote:
Originally Posted by Da Big_G
According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...
What prop are you using and with what motor? You might want to try a prop with less pitch. I have a little zaggi that had too much pitch and when I punched the throttle it would roll real bad.
Aug 29, 2012, 11:25 AM
Registered User
jsmith285's Avatar
Quote:
Originally Posted by Da Big_G
According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...
Whats your setup, Motor, prop, servos?
Aug 29, 2012, 11:41 AM
inverted-i-fly
3drcparts's Avatar
Quote:
Originally Posted by Da Big_G
According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...
me too, flys like s$%^

omega 72g, 11x5.5 prop, hs-65mg all around
Aug 29, 2012, 11:45 AM
fly and then fly some more!
nickelbn1's Avatar
Quote:
Originally Posted by Da Big_G
According to 3DHS, everyone that has had a roll problem via the warped wing and did the "twist" thing now has a correct flying plane. I now have both SFG (wing-tips) parallel, but it flies worse now. I think the warp is close to the fuselage, where any correction is minimal. Am I the only one that still has a problem with trim/roll that is speed sensitive? How about a foamie 3D alternative to this plane?...
Mine has gotten better after twisting but still has the roll issue some at higher speeds. A little ways back in the forum we talked about a epp sbach that is really good. Might want to check it out. The hokusei sbach 342.
Last edited by nickelbn1; Aug 29, 2012 at 11:55 AM.
Aug 29, 2012, 12:50 PM
"Get off the runway!"
Da Big_G's Avatar
Quote:
Originally Posted by jsmith285
Whats your setup, Motor, prop, servos?
Turnigy D3536/8 1000kv. motor
Turnigy 45a SBEC speed control
APC 12-6E prop
Turnigy 3C/1600 ma battery
HiTech HS-65MG servos all around.
Aug 29, 2012, 12:59 PM
Registered User
dentalpain's Avatar
My setup:
Motrolyfly 2810-1000 12x6 apc
HS65 MG tail, HB wing
Ice 50 w.new gens 3s 1300 25c
Built it the same was as my 34 extra EPP, 38 slick EPP and 48 Extra full EPP.

Honestly, I didnt take the time to twist (b/c I figured it was a patch at best), I took took the electronics out and dumped em in a 47 SHP. I was dissappointed, but you can't win em all.
Last edited by dentalpain; Aug 29, 2012 at 01:13 PM.
Aug 29, 2012, 01:35 PM
fly and then fly some more!
nickelbn1's Avatar
Quote:
Originally Posted by Da Big_G
Turnigy D3536/8 1000kv. motor
Turnigy 45a SBEC speed control
APC 12-6E prop
Turnigy 3C/1600 ma battery
HiTech HS-65MG servos all around.
Well part of your problem is the 12x6 prop. Seversl have reported that prop will cause more roll problems. Try a 11x5.5e.
Aug 29, 2012, 01:45 PM
"Get off the runway!"
Da Big_G's Avatar
Quote:
Originally Posted by nickelbn1
Well part of your problem is the 12x6 prop. Seversl have reported that prop will cause more roll problems. Try a 11x5.5e.
I don't think a smaller prop. is the answer. The roll is present in a low/no throttle down line. Only after some air speed bleeds off does the roll cease. BTW, I need considerable aileron trim for low speed flight. I was holding out for corrected wing to be available, but that is not going to happen. Not going to waste any more time on this one. I think I'll chuck it into the trash.
Aug 29, 2012, 01:49 PM
My hovercraft is full of eels.
Quote:
Originally Posted by nickelbn1
A little ways back in the forum we talked about a epp sbach that is really good. Might want to check it out. The hokusei sbach 342.
That's the 39" BX or V2 and it's wonderful! Unfortunately, they are out of stock at F3A Unlimited but BestRC has the red ones in stock.

It's Wednesday! Yay! Time for our weekly, after work, fun fly at the park. I brought the Edge, Sbach, Crack Pitts, Fishcopter (my quad) and many batteries.
Aug 29, 2012, 01:56 PM
fly and then fly some more!
nickelbn1's Avatar
Quote:
Originally Posted by dentalpain
My setup:
Motrolyfly 2810-1000 12x6 apc
HS65 MG tail, HB wing
Ice 50 w.new gens 3s 1300 25c
Built it the same was as my 34 extra EPP, 38 slick EPP and 48 Extra full EPP.

Honestly, I didnt take the time to twist (b/c I figured it was a patch at best), I took took the electronics out and dumped em in a 47 SHP. I was dissappointed, but you can't win em all.
That SHP is a pretty plane. Flown it yet?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold ... hosam Aircraft - Electric - Airplanes (FS/W) 1 Jul 17, 2012 10:23 PM
Sold 47" 3D Hobby Shop Edge 540.. LPU SteveT. Aircraft - Electric - Airplanes (FS/W) 1 Mar 11, 2012 07:58 PM