New Products Flash Sale
Thread Tools
Old Jul 25, 2012, 11:01 AM
eitan is offline
Find More Posts by eitan
Registered User
Quote:
Originally Posted by healthyfatboy View Post
Do you have voltage on the 5V rail for M2-M8 on the board? If you disabled the BEC on the 2nd and 3rd motor, then your servo won't get any voltage as the BEC from the 1st motor is separate from the rest of the connections.
Thank you !!!
I think you're right ...
I disabled the other two controllers BEC.
I'll check and I'll update the thread
Sign up now
to remove ads between posts
Old Jul 25, 2012, 02:57 PM
shelterock is offline
Find More Posts by shelterock
Fly, crash, rebuild.
Quote:
Originally Posted by eitan View Post
What could be the reason that the servo does not respond at all?
I use this servo: http://www.hobbyking.com/hobbyking/s...idProduct=8761.
The servo worked fine with the HobbyKing Multi-Rotor Control Board V2.1.
Thank you
Besides the BEC being disabled on #2-8, make sure ch4 is set to servo and not esc.
H
Old Jul 25, 2012, 06:18 PM
eitan is offline
Find More Posts by eitan
Registered User
Thank you all, The problem was solved with the connection to the second BEC.
Old Jul 26, 2012, 08:06 PM
healthyfatboy is offline
Find More Posts by healthyfatboy
Registered User
I have a Hitec HS-5085MG digital servo coming so I'll give that a try and see how well it works for the yaw.
Old Jul 27, 2012, 04:03 PM
Phalanx-0 is offline
Find More Posts by Phalanx-0
Hulk likes flying things
Phalanx-0's Avatar
So far it seems that the "jitter" and other problems are user errors.
It can happen. There are alot of things to remember and configure.
Is the board , or programming at fault?
It hasn't been shown to be.
Old Jul 27, 2012, 06:26 PM
rcbif is offline
Find More Posts by rcbif
Do a Barrel Roll!
rcbif's Avatar
Quote:
Originally Posted by Phalanx-0 View Post
So far it seems that the "jitter" and other problems are user errors.
It can happen. There are alot of things to remember and configure.
Is the board , or programming at fault?
It hasn't been shown to be.
Nobody I've heard of has shelled out 50$+ yet for a quality digital micro servo. I've read only one case where a budget digital worked. Kk himself said there is an issue where sub quality servos may not work. So yes, its a problem with the board.
Old Jul 27, 2012, 08:30 PM
Phalanx-0 is offline
Find More Posts by Phalanx-0
Hulk likes flying things
Phalanx-0's Avatar
Quote:
Originally Posted by shelterock View Post
So I installed a solar digital servo for $12 from hobbypartz. D657. 25g with 3.0kg 0.1 seconds to 60'. No wobble. Set servo on high. Sweet. $12 fix and tri is good!! H
hrm...wasn't even a $50 servo either.
I guess someone's not paying attention in their own thread.
Old Jul 27, 2012, 10:14 PM
rcbif is offline
Find More Posts by rcbif
Do a Barrel Roll!
rcbif's Avatar
Quote:
Originally Posted by Phalanx-0 View Post
hrm...wasn't even a $50 servo either.
I guess someone's not paying attention in their own thread.
Quote:
Originally Posted by rcbif View Post
Nobody I've heard of has shelled out 50$+ yet for a quality digital micro servo. I've read only one case where a budget digital worked. Kk himself said there is an issue where sub quality servos may not work. So yes, its a problem with the board.
Old Jul 28, 2012, 05:15 AM
Tim Harbour is online now
Find More Posts by Tim Harbour
DLG Bug Bit Me
Tim Harbour's Avatar
Quote:
Originally Posted by Phalanx-0 View Post
hrm...wasn't even a $50 servo either.
I guess someone's not paying attention in their own thread.

If you're not trying to sort this problem out 1st hand yourself then you clearly have no experience or constructive advice to pass on.
Out.
Old Jul 28, 2012, 12:18 PM
healthyfatboy is offline
Find More Posts by healthyfatboy
Registered User
I bought a decent, quality servo so once it gets in, I can test it out. Patience grasshopper!
Also, why does it have to be $50+?
Old Jul 28, 2012, 12:35 PM
rcbif is offline
Find More Posts by rcbif
Do a Barrel Roll!
rcbif's Avatar
Quote:
Originally Posted by healthyfatboy View Post
I bought a decent, quality servo so once it gets in, I can test it out. Patience grasshopper!
Also, why does it have to be $50+?
It dosent, but most of the brand name fastest digital servos are around that range which is what is supposed to work with this board in it's current config.
Old Jul 28, 2012, 10:57 PM
crezzee is offline
Find More Posts by crezzee
Build Fly Crash Repeat
crezzee's Avatar
From the kk2 thread:

Quote:
Originally Posted by knutek View Post
Hi and thank you for a great board.
Does this mean you have a FW update ready soon?

Quote:
Originally Posted by kapteinkuk View Post
No, it is lot of stuff left to do.


Looks like there will be no firmware solution for the tail servo problem anytime soon
Old Jul 28, 2012, 11:10 PM
slowjett is offline
Find More Posts by slowjett
-NEFPV-
So an consensus on which servo actually works here people?
Old Jul 28, 2012, 11:43 PM
healthyfatboy is offline
Find More Posts by healthyfatboy
Registered User
I'll try out the Hitec HS-5085 next week when it comes in. I'll try to get a video with the HS-85MG and the HS-5085MG to show a difference.
Old Jul 29, 2012, 09:05 AM
Phalanx-0 is offline
Find More Posts by Phalanx-0
Hulk likes flying things
Phalanx-0's Avatar
What board isolation solutions have been tried, and failed or succeeded?


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Hobbyking KK2.0 Multi-rotor LCD Flight Control Board MoRaLeSD Multirotor Talk 5 Apr 09, 2014 12:05 PM
Discussion Tricopter tail servo parts TS00 Multirotor Talk 5 Jun 23, 2012 02:40 PM
Discussion Problem Flashing Hk Board for Tricopter timmerflyer Multirotor Talk 0 Jun 20, 2012 01:10 PM
Help! TriCopter with HK Board V2 Savage27 Multirotor Talk 0 Jun 12, 2012 04:44 PM
Discussion .hex firmware for hk board tricopter emberjelly Multirotor Talk 1 Sep 25, 2011 06:33 AM