Thread Tools
Old Jul 30, 2012, 09:00 AM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
Get em while they are hot!
Sign up now
to remove ads between posts
Old Jul 30, 2012, 09:27 AM
WiseDuck is offline
Find More Posts by WiseDuck
Mmmmmmm!
WiseDuck's Avatar
Bit low on cash at the moment! And it seems like the KK2 board + delrin case just will not fit on the frame that's coming my way. It would block the power-distribution pads and make it impossible to hook up the wires. Maybe if I order another KK2 board!
Old Aug 12, 2012, 05:57 PM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
Ttt
Old Aug 12, 2012, 06:18 PM
dart50 is offline
Find More Posts by dart50
DART
I don't get it.
You are protecting board but not protecting the most sensitive it part - LCD display.
How so?
Old Aug 12, 2012, 06:22 PM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
Ask everyone who has bought one. My main concern when designing the case was to protect the board as much as possible from crash damage. Sure, there is always a chance that the board could get damaged in a crash, but being in an enclosure limits the type of damage that can happen. A destroyed center frame with a mounted board can easily result in broken pc boards or broken traces. This would protect the board from such damage. Like anything with an LCD, it still remains vulnerable, but in this case, it would take a direct impact by a stick, or other object to damage the LCD. Any prevention is better than nothing.

Make any more sense?
Old Aug 12, 2012, 06:36 PM
dart50 is offline
Find More Posts by dart50
DART
It's easy to make acrylic window for display - just cut it with laser and glue over your case.

Quote:
destroyed center frame with a mounted board can easily result in broken pc boards or broken traces
that is why board should be mounted on plastic stands - stands will break faster than board and the board will survive
Old Aug 12, 2012, 06:38 PM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
Thank you for your input. I wish I had a laser to play with
Old Aug 12, 2012, 06:43 PM
dart50 is offline
Find More Posts by dart50
DART
When I need laser I go to outdoor advertiesment guys and they do the job.
Can't you use milling machine for Acryl?
Last edited by dart50; Aug 12, 2012 at 06:49 PM.
Old Aug 15, 2012, 11:50 AM
SDSURFnGLIDE is offline
Find More Posts by SDSURFnGLIDE
Multi rotors=No Paycheck left
SDSURFnGLIDE's Avatar
Just ordered one of these....Thanks for the good work Chris
Old Aug 16, 2012, 02:42 AM
biz18434 is offline
Find More Posts by biz18434
Registered User
Hello Chris,
Can you please add another hole to the top of the case for the built in voltage alarm.
Thank You,
Biz
Old Aug 16, 2012, 08:44 AM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
SDSurf,

Thanks for the order! It will ship out in today's mail.

Biz,

I will revise the drawing, and add a hole there. Thanks for the input!

Chris
Old Aug 16, 2012, 10:47 AM
SDSURFnGLIDE is offline
Find More Posts by SDSURFnGLIDE
Multi rotors=No Paycheck left
SDSURFnGLIDE's Avatar
Quote:
Originally Posted by Chris Moon View Post
SDSurf,

Thanks for the order! It will ship out in today's mail.
Biz,

I will revise the drawing, and add a hole there. Thanks for the input!

Chris
you are welcome and thank you
Old Aug 20, 2012, 12:05 PM
SDSURFnGLIDE is offline
Find More Posts by SDSURFnGLIDE
Multi rotors=No Paycheck left
SDSURFnGLIDE's Avatar

Case Review


So I ordered one of these cases and I would have to say this is going to definitely save me a$$ in any type of crash i may be in!!

Very well built and strong. I like how the bolts are black to match the case...not that it is neccessary....but its nice for those who like the "clean" build look.

The only thing I would say needs to be changed is the slots where the servo leads go in...both on the motor and rx....they were ever so slightly too small and i had to cut away some material in order to allow me to slide those in easily. I used an exacto knive and just a few scrapes back and forth did the job...this could also be done with some course sand paper too I bet...I took the material away from outer edge since the inner edge was already very thin...

But overall this is a very well built product and for the price, you cannot beat it!! I should also mention that I received my case very promptly!!

So thank you Chris!! can't wait to see what you come up with next.
Old Aug 22, 2012, 07:13 AM
flarssen is online now
Find More Posts by flarssen
Registered User
What is the distance between the screw lugs? If it was the same as the hole pattern of the board itself, it would be useful for mounting on frames designed for boards that mounts diagonally, like Q450 from HobbyKing.

Fred
Old Aug 22, 2012, 02:42 PM
Chris Moon is offline
Find More Posts by Chris Moon
Registered User
Fred,

The distance across to the screw centers are 2.3" exactly.

What is the distance diagonally for the Q450 frames?

Chris


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product Hobbyking i86 Delrin Case Chris Moon Multirotor Talk 16 Jul 30, 2012 09:00 AM
Sold SOLD - HoverFly Sport board, Maxbotix LV-EZ0 sonar, MadLabs protective case ross_badger Aircraft - Electric - Multirotor (FS/W) 1 Jun 27, 2012 06:36 AM
Sold NAZA w/ Protective delrin casing The RevKev Aircraft - Electric - Multirotor (FS/W) 4 May 07, 2012 06:26 PM
Discussion Hoverfly Pro Green Board Protective Case Greasetattoo Aerial Photography 6 Apr 05, 2012 06:43 PM
For Sale PSP + 2 gb card + game + case + screen protecter hamcigar Non R/C Items (FS/W) 0 Apr 16, 2006 11:30 PM