FinwingHobby Universeye Penguin Review/Build/Discussion Thread - ReadyMadeRC.com - Page 87 - RC Groups
Thread Tools
Jan 27, 2013, 10:11 AM
Registered User
imagebuff's Avatar
Quote:
Originally Posted by SRush99
Flew mine again today with my GoPro 3 attached. Winds were 10 - 15 mph. Flew great with the washers at the bottom motor mount holes. I guess as the commercial goes - "your results may vary" when it comes to setting the thrust line of the motor. I also found that the upgraded canopy will get blemished by sunscreen ( it was in the mid 70s today in Texas !) . I tried cleaning the blemishes off with dishwashing liquid with no luck. Also used windex - no change. If you buy one be very careful!
Great news Stuart! About the washers anyway . I also flew mine again, just down the street from Stuart, same winds, full FPV gear, Gopro 3, Washers on THE BOTTOM- no more lurching upward on throttle! Washers on the bottom are the way to go in my opinion.

Now the bad news - my 2815 motor started cutting out. I'm running 4S with a 60 amp ESC. I'm going to an NTM 3536 which I know runs well on 4S.
Sign up now
to remove ads between posts
Jan 27, 2013, 12:02 PM
Registered User
Will Krylon work over packing tape? I taped up my plane yesterday but I don't know how I want to paint it yet.
Jan 27, 2013, 12:38 PM
Registered User
tape should be easy to remove just go slow, I used 3m storage and it came right off
Jan 27, 2013, 12:40 PM
Registered User
TAREK.SAADE's Avatar
PENGUIN FPV 27 01 2013 Landing (1 min 18 sec)
Jan 27, 2013, 01:26 PM
Registered User
Those wings sure do create alot of lift..lol, nice landing to.
Jan 27, 2013, 01:38 PM
Registered User
CheckSum's Avatar
Quote:
Originally Posted by SRush99
[...]I also found that the upgraded canopy will get blemished by sunscreen ( it was in the mid 70s today in Texas !) . I tried cleaning the blemishes off with dishwashing liquid with no luck. Also used windex - no change. If you buy one be very careful!
Sunscreen will also eat the clear coat off your 2009 Subaru Outback too if your wife gets it all over it.
Jan 27, 2013, 02:32 PM
Registered User
have a set of butt cheeks?
Jan 27, 2013, 08:10 PM
Registered User
I have my 2815 motor setup like in the manual with the "3mm" washers on the top. I personally have not had any probs with it setup like this. I can punch the throttle and it will keep flying in a strait line.

I have read that the C of G in the manual is 15-20mm to far back. Is this true? I have yet to test it myself, but how many of you have tried flying you Penguin with the C of G 15-20mm forward from the manual C of G? How is it?
Jan 27, 2013, 08:30 PM
Registered User
ron-sand's Avatar
CG om a model/airplane is to a degree an subjective thing based on your flying experience and preference. In addition comes of course how the airframe behaves based on amongst other its weight, incidence of tail plane to main wing, motor thrust angle, wing profile etc.

I have set the tail to main-wing incidence at 2 deg (was 3.5 deg), and have the CG at 90-95mm from wing leading edge. I use 2mm washers on the top motor mounts.

If I where you, I wold start with the recommended 85mm and take it from there.
Jan 27, 2013, 10:39 PM
Registered User
SRush99's Avatar
Quote:
Originally Posted by Guru06
Will Krylon work over packing tape? I taped up my plane yesterday but I don't know how I want to paint it yet.
I haven't had any luck with paint sticking to packaging tape.
Jan 28, 2013, 05:27 PM
Registered User
SWAMPER's Avatar
what paints work on this foam was going to use the short cuts paint but not many colors to pick
Jan 28, 2013, 05:50 PM
KK4NOP
Mike Freas's Avatar
Quote:
Originally Posted by SWAMPER
what paints work on this foam was going to use the short cuts paint but not many colors to pick
I think the key is a good wet sanding with 400 grit or finer and some dish soap. The parts I did this way the paint sticks much better.
Jan 29, 2013, 01:48 AM
Registered User
surfer dude's Avatar
Subscribed
Jan 29, 2013, 02:12 AM
Aerial Operator
Quote:
Originally Posted by SWAMPER
what paints work on this foam was going to use the short cuts paint but not many colors to pick
Try PlastiDip spray. It is rubber based so it will be more durable than other spray paints.

Cheers,
Jan 29, 2013, 03:16 PM
Aerial Operator
Hey guys I have no spacers on my motor mount and the penguin flies pretty good. Do you guys recommend the 3mm spacers on the top of the motor mount?

Thanks


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion fmkit's ULink (review/discussion/etc) CrashMeUp FPV Talk 112 Apr 07, 2013 06:34 PM
Discussion general engine discussion thread cale10 Engines 273 Nov 13, 2012 02:22 PM
Spektrum DX7 technology discussion (moved from review thread) Chipwillis Radios 62 Jan 17, 2007 05:07 PM
Heliup.com CNC CF Shogun/Zoom frame build thread/review Hoverup Mini Helis 123 Jun 18, 2005 10:09 PM