Thread Tools
Jul 26, 2012, 04:40 PM
Anti-Gravity
Quote:
Originally Posted by Jochen222
Hi,
I use a transistor NPN (for example) BC547 with base resistor to pin 32 - that works an MultiWii.
So, unlike the SE, this board will not work w/o a driver?
Sign up now
to remove ads between posts
Jul 26, 2012, 04:50 PM
James not bond
jy0933's Avatar
where can i buy those 4 pin white connector with wires?

thanks
Jul 26, 2012, 07:13 PM
Registered User
So, does this mean my new Multiwii MWC FC CN-06 GPS Receiver, unopened GPS is useless? Which GPS did you end up going with, I'm planning on using MW software, but don't have the knowledge/skills to add an eeprom to my current GPS.

Quote:
Originally Posted by nebstress
When you have made all the changes & sent them you need to save them, go to "Receiver" then down to "Action" & click on "Save Config".

The settings will reset within 8 - 24 hours of no power if you are using "Multiwii MWC FC CN-06 GPS Receiver", this is very frustrating so I have given up using this GPS module with the CRIUS AIOP.
Jul 26, 2012, 08:07 PM
Registered User
RTH test and crash

Test CRIUS AIO return home and Crach (0 min 13 sec)
Jul 26, 2012, 08:17 PM
Registered User
I need help. I have the Crius AIO Pro and the GPS. The board works fine with both wii gui and wingui. The GPS is configured per FPV central with the ucenter. GPS works good with ucenter and is configured 115200/ 100ms/10, etc. and shows good data. Plugged in to the AIO the power light comes on, but no data or sats on either GUI. Wiring checked and re-soldered. What next?
Jul 26, 2012, 08:30 PM
Registered User
What GPS module you using?
Seems like people who are using that 06 model are having issues without doing the Eeprom mod or what ever it is
Jul 26, 2012, 09:00 PM
Registered User
Quote:
Originally Posted by MrFawlty
Thx alot Mis_B for the info. awesome!
Do i need a transistor or something between pin 33 and the leds?
thx again
Yes, if you use 12V led strips's or other 12V led's.
Get some NPN transistor (0.5A of collector current or better) add 1kohm resistor series in base, connect second terminal of resistor to pin 33 of AIO, connect emiter to GND and collector to - point of LED's. + LED's to +battery.
Jul 26, 2012, 09:29 PM
Registered User
I guess the 06. I got it recently from RC Timer (controller board too). yes, with magnifier the board for the GPS has "CN06"
Jul 26, 2012, 09:47 PM
Registered User
Quote:
Originally Posted by ezsport
I need help. I have the Crius AIO Pro and the GPS. The board works fine with both wii gui and wingui. The GPS is configured per FPV central with the ucenter. GPS works good with ucenter and is configured 115200/ 100ms/10, etc. and shows good data. Plugged in to the AIO the power light comes on, but no data or sats on either GUI. Wiring checked and re-soldered. What next?
YOU SAME MY PROBLEM
I USE THIS CONFIG

#define GPS_SERIAL 3
#define GPS_BAUD 115200

AND USE TX3,RX3
Jul 26, 2012, 10:03 PM
Registered User
Thanks ibooo for the response. I read somewhere that TX/RX 3 are for something else, but if it works I can only think we are moving away from something defined somewhere about serial 2.
Jul 26, 2012, 10:24 PM
Registered User
Anyone else still waiting on this FC or other parts to come in before they can fly?

Because the anticipation is KILLING ME

am I alone? lol
Jul 27, 2012, 12:08 AM
member of TheBlindHawks
careyer's Avatar

Orientation of Crius AIO Pro1 in MPNN


Quote:
Originally Posted by Jochen222
Hi,

thanks a lot to Sir Alex!

Now the board has with MPNG the same orientation as in MWC !!! Im happy!
Does that mean that from now on one must not mount the FC rotated by 45degrees (compared to MWC) on the frame when using MPNG?
Currently designing a new frame and i wonder if i need to drill holes for normal mount AND 45degree offset mount.

Thanks for your answer!
Thomas Berndt
Jul 27, 2012, 12:31 AM
Registered User
Kicking around the idea of giving MegaPirate a try, but have a couple questions.

1. What's the learning curve like on MegaPirate? I consider the Multiwii learning curve pretty steep, but I'm quite familiar with it now, not sure if I want to start learning all over again.
2. How difficult is it to switch back and forth on this board? Relatively simple like just flashing the firmware, and changing the board orientation (since I heard the orientations were different). Or do you have to totally change all the motor outputs around, reconfigure your tx, recalibrate esc's, and a bunch of other stuff?
Jul 27, 2012, 02:01 AM
Registered User
Borneoben's Avatar
Quote:
Originally Posted by scribble007
Anyone else still waiting on this FC or other parts to come in before they can fly?

Because the anticipation is KILLING ME

am I alone? lol

You are not alone!

Mine is due to arrive very soon!
Jul 27, 2012, 05:40 AM
Registered User
Jeppie's Avatar
@ Careyer;
For MPNG turn it 90 deg clockwise (not 45 deg).


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Mini-HowTo Arduino and HobbyKing Multi-Rotor Control Board V3.0 or KKmulticontroller v5.5 pprioverde Multirotor Drone Talk 33 May 28, 2017 11:40 AM
Discussion New updated Crius Multiwii SE flight controller SGsoar Multirotor Drone Electronics 72 May 15, 2013 08:36 PM
Discussion Jim, any plans for more multi rotor flight controller? chris24g Xtreme Power Systems 12 Jun 25, 2012 08:11 PM
Sold One New, one used ArduPilot 2560 APM1.0 Flight Controlls/autopilots wingspinner FPV Equipment (FS/W) 3 May 28, 2012 12:55 AM
Question Quad Build Using HobbyKing Multi-Rotor Control Board V3.0 (Atmega328 PA) SJackson Multirotor Drone Talk 27 Apr 30, 2012 08:51 PM