CRIUS ALL IN ONE PRO v1.0 Multi Rotor Flight Controller - Page 228 - RC Groups
Shop our Airplanes Products Drone Products Sales
Thread Tools
Nov 13, 2012, 04:43 AM
Registered User
Thank you Sir Alex for the update,yours Marty.
Sign up now
to remove ads between posts
Nov 13, 2012, 05:10 AM
Registered User
Quote:
Originally Posted by Sir Alex
I'm very busy now and this week, so MPNG will be released next week...
Is there a place where I can read whats changed in the new version?
Nov 13, 2012, 05:17 AM
Aleksey Kharlanov
Quote:
Originally Posted by Goofy68
Is there a place where I can read whats changed in the new version?
Of course, you can read at DIYDrones site: http://diydrones.ning.com/forum/cate...istForCategory
Nov 13, 2012, 06:19 AM
Registered User
Quote:
Originally Posted by Sir Alex
Of course, you can read at DIYDrones site: http://diydrones.ning.com/forum/cate...istForCategory
Thankyou
Nov 13, 2012, 08:42 AM
Registered User
Quote:
Originally Posted by Sir Alex
I'm very busy now and this week, so MPNG will be released next week...
Hooray! Thank you!
Nov 13, 2012, 01:59 PM
Registered User
Hello,
I would like to use a remote controlled switch like this one :
http://www.hobbyking.com/hobbyking/s...d_Switch_.html

to on / off some night lights?
Where could it be connected and what code do I need to change in megapirateng?

Best regards,
jeff
Nov 13, 2012, 02:54 PM
Registered User
crash8384's Avatar
Quote:
Originally Posted by scribble007
Never heard of it.
Whats the difference?
yes if you have bell or pancake motors you will need to flash your escs to wiiesc thru the new kk flash tool from lazyzero. i think its called 0.7 beta . i have it and seen the wiiesc flash on there.

its a known issue that simonk and flat motors dont like each other but the wiiesc flash will fix that.
Nov 13, 2012, 04:07 PM
Registered User
1-2-hak's Avatar
Quote:
Originally Posted by Sir Alex
I'm very busy now and this week, so MPNG will be released next week...
Thats great news as I was having trouble trying to port it myself.

Sir Alex - would you mind updating the porting method on the wiki so we can get some more insight for the next version.

Thanks
Nov 13, 2012, 04:13 PM
Registered User
All,
With the Extend Board for AIO PRO FC which GPS baud should I use?
Do I need to setup the GPS as for a standalone GPS?

Also I bought the 3DR radio from RCTIMER, do I need to separate the XBEE from it? Is there any XBEE that will work with the extend board with the 3DR from RCTIMER?
Antoine
Nov 13, 2012, 04:15 PM
Registered User
Quote:
Originally Posted by crash8384
yes if you have bell or pancake motors you will need to flash your escs to wiiesc thru the new kk flash tool from lazyzero. i think its called 0.7 beta . i have it and seen the wiiesc flash on there.

its a known issue that simonk and flat motors dont like each other but the wiiesc flash will fix that.
I have the bell RC timer 2830 1000kv motors. And like I said. 3 of the 4 work fine after flashing. So Im thinking I might have screwed something up.
Should I order another motor and esc and try flashing again. Or just order a new preflashed esc?
Nov 13, 2012, 04:26 PM
Registered User
new simonk firmware works fine with pancake motors. it just took him a long time to fix the problem.
Nov 13, 2012, 07:45 PM
Multicopter Nut
ThePara's Avatar
Quote:
Originally Posted by crash8384
yes if you have bell or pancake motors you will need to flash your escs to wiiesc thru the new kk flash tool from lazyzero. i think its called 0.7 beta . i have it and seen the wiiesc flash on there.

its a known issue that simonk and flat motors dont like each other but the wiiesc flash will fix that.
I use RcTimer 5010 360 Kv pancakes since April on SimonK-ized 20A ESCs without any issues. And lately I setup a hexa on AX-4008Qs and it's running smooth as well.
Nov 13, 2012, 07:47 PM
Registered User

pre flashed escs


do the pre flashed escs have a bootloader such that they can be re-flashed/updated through the receiver wire?
Nov 13, 2012, 08:00 PM
Too Many Thread Subscriptions
TheFernMan's Avatar
Quote:
Originally Posted by A Monell
do the pre flashed escs have a bootloader such that they can be re-flashed/updated through the receiver wire?
Yes. Using lazyzero flashing tool.

Edit: sorry, they have to have had the bootloader loaded when they were flashed. I haven't seen store with preflashed ESCs with bootloader enabled

Edit2: forgot. Abusemark sells them with bootloader.
Nov 13, 2012, 09:14 PM
Registered User
failed to leave programming mode


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Mini-HowTo Arduino and HobbyKing Multi-Rotor Control Board V3.0 or KKmulticontroller v5.5 pprioverde Multirotor Drone Talk 33 May 28, 2017 12:40 PM
Discussion New updated Crius Multiwii SE flight controller SGsoar Multirotor Drone Electronics 72 May 15, 2013 09:36 PM
Discussion Jim, any plans for more multi rotor flight controller? chris24g Xtreme Power Systems 12 Jun 25, 2012 09:11 PM
Sold One New, one used ArduPilot 2560 APM1.0 Flight Controlls/autopilots wingspinner FPV Equipment (FS/W) 3 May 28, 2012 01:55 AM
Question Quad Build Using HobbyKing Multi-Rotor Control Board V3.0 (Atmega328 PA) SJackson Multirotor Drone Talk 27 Apr 30, 2012 09:51 PM