|
|
|
|
Thread OP
|
New Product
CRIUS ALL IN ONE PRO v1.0 Multi Rotor Flight Controller  ◆Features: •Support MegaPirateNG / ArduPlaneNG / ArduCopterNG / MultiWii / AeroQuad firmware •8-axis motor output •8 input channels •4 serial ports (S0~S3) •2/3-axis gimbal system •6 Analog port for extend device (A0~A5) •I2C port for extend sensor or device •Separate 3.3V and 5V 500mA LDO voltage regulator •ATMega 2560 Microcontroller •MPU6050 6 axis gyro/accel with Motion Processing Unit •HMC5883L 3-axis digital magnetometer •MS5611-01BA01 highprecision altimeter •FT232RQ USB-UART chip and Micro USB receptacle •On board logic level converter •Dimension: 50mmX50mm •45x45mm mounting holes •Height: 11.6mm •Weight: 14.2g •Hole diameter: 3mm •Match the standard of RoHS ◆Package content •AIO PRO FC x 1 •3Pin to 1Pinx3 cable 100mm x 3 •3Pin to 3Pin cable 100mm x 1 •Molex 1.25mm 4Pin cable 100mm x1 •Molex 1.25mm 6Pin cable 100mm x2 •Molex 1.25mm 8Pin cable 100mm x1 ================================================== ==== Warning! Issues of clone board : https://www.rcgroups.com/forums/show....php?t=1790506 Thanks jabram very much! ================================================== ==== |
|
|
Last edited by mealie; Dec 20, 2012 at 03:17 PM.
|
|
|
|
|
|
|
were can we buy ??
|
|
|
|
|
|
|
|
|
How soon? I don't want to wait 2-3 months.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
|
Quote:
I believe the advantage of this board is that it runs both MultiWii and MegaPirateNG and has all four sensors onboard (gyro, acc, baro, compass), together with the ATMega 2560. It's a lot cheaper than the APM 2, even if you add GPS. It is, however, more expensive than http://www.goodluckbuy.com/mwc-multi...ard-quadx.html |
|
|
|
Last edited by Lorphos; Jun 24, 2012 at 05:27 PM.
|
|
|
|
|
|
Meh megapirate comes with 10 dof and runs MWC and Megapirate-ng code on a 2560 for $65.
I don't see the point in the high price for this one. http://www.ebay.co.uk/itm/Pirate-Fli...#ht_3546wt_923 |
|
|
|
|
|
|
|
Thread OP
|
The IMU board used BMP085, low precision baro.
The main board no FTDI circuit and voltage regulator. So it is cheap. http://rover.ebay.com/rover/1/710-53...3ht_3546wt_923 http://www.goodluckbuy.com/mwc-multi...ard-quadx.html |
|
|
Last edited by mealie; Jun 25, 2012 at 02:50 AM.
|
«
Previous Thread
|
Next Thread
»
| Thread Tools | |
| Similar Threads | |||||
| Category | Thread | Thread Starter | Forum | Replies | Last Post |
| Mini-HowTo | Arduino and HobbyKing Multi-Rotor Control Board V3.0 or KKmulticontroller v5.5 | pprioverde | Multirotor Drone Talk | 33 | May 28, 2017 11:40 AM |
| Discussion | New updated Crius Multiwii SE flight controller | SGsoar | Multirotor Drone Electronics | 72 | May 15, 2013 08:36 PM |
| Sold | One New, one used ArduPilot 2560 APM1.0 Flight Controlls/autopilots | wingspinner | FPV Equipment (FS/W) | 3 | May 28, 2012 12:55 AM |
| Question | Quad Build Using HobbyKing Multi-Rotor Control Board V3.0 (Atmega328 PA) | SJackson | Multirotor Drone Talk | 27 | Apr 30, 2012 08:51 PM |