Thread Tools
Sep 21, 2012, 03:10 AM
Registered User
Quote:
Originally Posted by jalves View Post
Wiki Updated!!
Nice
Sign up now
to remove ads between posts
Sep 21, 2012, 04:23 AM
Registered User
Excelente trabalho Jalves!
Sep 21, 2012, 07:48 AM
Registered User
jalves's Avatar
Obrigado HF.

Anima-te e constrói um opendiyAT
Sep 22, 2012, 01:55 PM
Registered User
Is this right?
http://vimeo.com/49977639
Sep 22, 2012, 03:55 PM
Registered User
jalves's Avatar
Vikedal,

I couldn't understand much of your video, can you upload a improved (more focused, improved definition) video??
Sep 22, 2012, 04:49 PM
Registered User
Is this better?
What information will you see in the serial monitor?
http://vimeo.com/49983274
Sep 22, 2012, 05:18 PM
Build to Fly? FLY to BUILD!
Legot's Avatar
It seems like your serial monitor is at the wrong baud rate. It should work if you change the receiving rate to 9600 baud.
Sep 22, 2012, 05:35 PM
Registered User
It is at 9600... What should the other be?
Sep 22, 2012, 05:46 PM
Registered User
jalves's Avatar
When you power your arduino, do you see the welcome message "Projecto DIY_AT, Tx V02a-alfa" "Ready!"

EDIT:
If you are using the version from the repository (The Tx version) it should be 9600bps, if you are using the Rx version, it should be 38400bps.
Sep 23, 2012, 06:58 AM
Registered User
Quote:
Originally Posted by jalves View Post
When you power your arduino, do you see the welcome message "Projecto DIY_AT, Tx V02a-alfa" "Ready!"

EDIT:
If you are using the version from the repository (The Tx version) it should be 9600bps, if you are using the Rx version, it should be 38400bps.
Is it just "Projecto DIY_AT, Tx V02a-alfa" "Ready!" That should come?
Sep 23, 2012, 08:45 AM
Registered User
jalves's Avatar
Yes.

But if you uncomment
//print_data();

You should see more action, good to bench test, but avoid it in the model.
Sep 23, 2012, 11:18 AM
Registered User
final test (0 min 25 sec)


Is it ready?
Sep 23, 2012, 01:19 PM
Registered User
jalves's Avatar
I couldn't read any sentences in the serial monitor, but it seems you are good to go.

Now test it with the wireless link, airwaves modules are 100% compatible, any other brand has to be tested.
Sep 23, 2012, 01:25 PM
Registered User
So i do it the same way on the pc only wireless?
Sep 23, 2012, 03:44 PM
Registered User
jalves's Avatar
Yes, you remove the "blue" wire (see wiki) from pin 10 and connect to audioIN of your video Tx (don't forget to connect the ground wire between Video Tx and arduino), in the Rx part connect the audio OUT of the Video Rx to the arduino's pin2 (again, don't forget to connect GND between video Rx and arduino GND).


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! LRS/UHF/XPS for Aurora 9, and 1.3ghz Antenna Tracker. Eagleeyes or Skylark? daign FPV Talk 2 May 17, 2012 03:36 PM
Sold 360 Servo for (Antenna Tracker or PAN).....NEW crd FPV Equipment (FS/W) 1 Apr 15, 2012 05:39 PM
Sold RVGS Antenna Tracker scrape FPV Equipment (FS/W) 0 Mar 31, 2012 11:18 PM
Sold Antenna Pan/Tilt for Antenna Tracker w/ MG Servos imagebuff FPV Equipment (FS/W) 1 Mar 20, 2012 02:26 AM
Sold Servo City Heavy Duty Pan / Tilt for antenna tracker w EZ Antenna Tracker thefokker FPV Equipment (FS/W) 4 Sep 08, 2011 07:53 AM