



Discussion
iCharger 3010b and iCharger 306B
These are rated at 1000 watts, and the 306B is a 6S charger...but they both have a maximum charge current of 30 amps.
To get 1000 watts into 6S at 30 amps, each cell would have to be 5.56 volts. What am I missing? Granted, the 3010b can do 10S, and at 3.7 volts/cell, you hit 1000 watts at 27 amps. But I don't think the 306B can't hit 1000 watts charging 6S lipos at 30 amps. At 30 amps and 3.7 volts/cell, you're only hitting 666 watts. 






306b
1000 watts is not a lipo specific limit 12 Life cells  43.2v (23.1 amps for 1000 watts) 30 amps @ 25.2v (756 watts) is the 6s lipo limit Cheers 





Thanks guys.
What is a better charger? By better, I mean least $/effective watt when charging multiple 6S lipo batteries using a paraboard or similar (and can stand up to repeated high amp usage)? The Powerlab 6 does 40 amps, enough to charge 6 3300mah batteries at 2C, but I am afraid there is something I'm missing. 





Quote:
https://www.rcgroups.com/forums/show...h#post20578347 If you definitely need the full 40 amps on 6s with a 24v supply, the Powerlab8 is the just the ticket. 






When charging 6S, the PL6 will indeed offer higher power output if your power supply has sufficient voltage. IIRC, the PL6 will do somewhere around 850 watts on 24 volt input. Almost 30 volt input is required to hit 1000W output as it has a 40A input current limitation. The 306B is limited to 30A output so it'll take a bit longer to charge your 6S packs.
The 3010B offers nothing over the 306B when charging 6S lipolys. As such, it'd be wasted $, IMO, if one never planned to go above 6S lipoly. It'd be a tough decision for me personally. I have 4 iChargers (1 x 306B, 3 x 106B) and absolutely love them. I almost always run them at full current output and they have all been flawless. That said, I would love to have a PL6 for the extra 10A. Mark 



A little misleading. A ~1520% increase in charge power does not equate to a ~33% reduction in charge time. A fair test would be to do repeated tests with an actual 306B compared to a PL6 using the same batteries discharged to the same voltage.
Agreed that the PL6 will have lower total charge times, but not by ~33% when charging 6S lipoly from a 24 volt source. Mark 
Last edited by mrforsyth; May 09, 2012 at 12:53 AM.





Huh, guess I didn't see that.
Well epbuddy has the power lab 6 with a paraboard and the usb interface for $198 + shipping. The 306b (which includes usb) comes with a free paraboard for $160 + shipping. The 306b has ~50A input current limit compared to the PL6's 40A, meaning you won't need as much voltage from a dc power supply. If you've got a 30V+ power supply I'd go with the PL6. But if you're going to use a 24V or less dc supply I'd get the 306b. With a 24V supply you'd only get approx. 32.38A of charging current on the PL6, not much faster really. If you've got smaller than 6s batteries then you might like the extra 10A of charging current you'd be able to get that the PL6 has. 

Last edited by Rayne; May 09, 2012 at 02:01 AM.

Thread Tools  
Similar Threads  
Category  Thread  Thread Starter  Forum  Replies  Last Post 
Discussion  iCharger 1010B+, 106B+, 208B, 206B, 306B and 3010B  junsi  Batteries and Chargers  16485  Yesterday 11:25 PM 
For Sale  Power supplies/Charging setups 306b TP820 3010b PL8 PL6 500/100w 700/1400w 12/24v  paulpeffly  Aircraft  Electric  Batteries & Chargers (FS/W)  2  Feb 22, 2012 08:24 AM 
For Sale  Power supplies/Charging setups 306b TP820 3010b PL8 PL6 500/100w 700/1400w 12/24v  paulpeffly  Aircraft  Electric  Batteries & Chargers (FS/W)  0  Feb 16, 2012 11:55 PM 
Found  Trade my 3010B 1000W iCharger for 2 smaller iCharger's  invert  Aircraft  Electric  Batteries & Chargers (FS/W)  5  Oct 28, 2011 12:49 AM 