Thread Tools
Old May 11, 2012, 04:39 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
I just got one of the FPV frames from QA and Paid 140.00 for it another friend of mine is getting one too. it is really nice and hope to start building it up this weekend.
Sign up now
to remove ads between posts
Old May 11, 2012, 05:34 PM
timnilson is offline
Find More Posts by timnilson
timnilson's Avatar
Quote:
Originally Posted by BenHayat View Post
It's painful to see sometime.... But you stick to your design, improvement, Customer Service and parts, and in long run, that prevails.
Hope that helps!
..Ben
Thanks Ben.
Site Sponsor
Old May 11, 2012, 06:20 PM
blade strike is online now
Find More Posts by blade strike
DJI Testing / US Support
blade strike's Avatar
QA is banned...enough said!

Looking forward trying Tims ...seems like he would be around for support q
Site Sponsor
Old May 11, 2012, 06:37 PM
tc3wins is offline
Find More Posts by tc3wins
Multirotor Builder!!!!!
Well I have nothing against either of them an i like both of the frames . And i wish Tim and QA the best with there frames. I am sure both will sell a lot of them. But on a side note. Just because QA is not on here any more doesn't mean he won't have support.
Old May 14, 2012, 04:20 AM
culexus is offline
Find More Posts by culexus
Registered User
Hi timnilson Is it possible to get a order to day? 200$ 250$ ?? for a frame
Old May 14, 2012, 07:41 AM
LexusFPV is offline
Find More Posts by LexusFPV
Registered User
Tim,
What is the approx. price for the Receiver Ready version?
(assembled w/the highend motors,ESC, props, etc....)
I already have a EzUHF tx/rx here.

PM me if you are still unsure of the ball park figure.
I can wait another month or so:-)
thanks much Tim.
Old May 14, 2012, 10:44 AM
timnilson is offline
Find More Posts by timnilson
timnilson's Avatar
Quote:
Originally Posted by culexus View Post
Hi timnilson Is it possible to get a order to day? 200$ 250$ ?? for a frame
We are in full swing making parts for the first production run. I will soon open the pre-order process for you to reserve your kit out of this first run.

Quote:
Originally Posted by LexusFPV View Post
Tim,
What is the approx. price for the Receiver Ready version?
(assembled w/the highend motors,ESC, props, etc....)
I already have a EzUHF tx/rx here.

PM me if you are still unsure of the ball park figure.
I can wait another month or so:-)
thanks much Tim.
I have not had time to assemble a parts list with prices. The way we price RTF kits is that we take a "Bill of Materials" which includes the cost of all the parts we use and then add a "Sourcing, Build, and Tuning" fee to it that covers the time and effort aspect.
Site Sponsor
Old May 15, 2012, 11:55 PM
timnilson is offline
Find More Posts by timnilson
timnilson's Avatar
I was able to run a vibration test with an iPhone and the "Vibration" app installed. I flew two hover flights with the QAV500 at about 6 feet inside. No wind, but maybe still a bit of ground effect and air being pushed around in the room. For one flight I strapped the iPhone to the top/clean part of the frame and during the other I strapped the iPhone to the dirty/bottom part of the frame. See the results of each in the below picture.

Site Sponsor
Old May 16, 2012, 01:12 PM
AeroVideoUS is offline
Find More Posts by AeroVideoUS
aka Helidaho
AeroVideoUS's Avatar
Quote:
Originally Posted by timnilson View Post
I was able to run a vibration test with an iPhone and the "Vibration" app installed. I flew two hover flights with the QAV500 at about 6 feet inside. No wind, but maybe still a bit of ground effect and air being pushed around in the room. For one flight I strapped the iPhone to the top/clean part of the frame and during the other I strapped the iPhone to the dirty/bottom part of the frame. See the results of each in the below picture.

That's COOL!
Old May 16, 2012, 04:25 PM
BenHayat is online now
Find More Posts by BenHayat
Always Excel >>>
BenHayat's Avatar
Quote:
Originally Posted by timnilson View Post
I was able to run a vibration test with an iPhone and the "Vibration" app installed. I flew two hover flights with the QAV500 at about 6 feet inside. No wind, but maybe still a bit of ground effect and air being pushed around in the room. For one flight I strapped the iPhone to the top/clean part of the frame and during the other I strapped the iPhone to the dirty/bottom part of the frame. See the results of each in the below picture.

Excellent!
Old May 18, 2012, 01:40 AM
rollinolin is offline
Find More Posts by rollinolin
Registered User

Price?


Any idea on the price?

Quote:
They have an M3 thread (that's very difficult to find on bobbins that exist out there), have an 8mm long stud
bobbins are not that hard to find
http://www.ebay.com/itm/RUBBER-MOUNT...item2311667cd6

will you sell just the center pieces so i may use my 10mm aluminum arms? the frame could be modded to adapt to them.

It would appeal to the people that dont have a lot of $$.

Price?

Also a suggestion
have you thought about putting the board and battery underneath the quad arms. Less vibrations if the battery and camera were to hang vice sit on top of the quad. All your mass is putting pressure on those vibration mounts. If all the weight of the battery and cameras were under the "dirty" part it would truly be isolated. The motors putting upward force and the clean section using gravity to pull down. It would be interesting to see the difference.
Last edited by rollinolin; May 18, 2012 at 01:47 AM.
Old May 18, 2012, 03:39 AM
daign is offline
Find More Posts by daign
My RC builds in my profile.
daign's Avatar
interesting design. I'll be keeping an eye on this one.
Old May 18, 2012, 03:45 AM
Orracle is offline
Find More Posts by Orracle
Registered User
Quote:
Originally Posted by rollinolin View Post
Also a suggestion
have you thought about putting the board and battery underneath the quad arms. Less vibrations if the battery and camera were to hang vice sit on top of the quad. All your mass is putting pressure on those vibration mounts. If all the weight of the battery and cameras were under the "dirty" part it would truly be isolated. The motors putting upward force and the clean section using gravity to pull down. It would be interesting to see the difference.
The bobbins are being used correctly in this case, they must always be used under compression, not suspension. You would need an entirely different mount for that purpose, such as a wire rope mount.

Old May 18, 2012, 10:17 AM
rollinolin is offline
Find More Posts by rollinolin
Registered User
Quote:
Originally Posted by Orracle View Post
The bobbins are being used correctly in this case, they must always be used under compression, not suspension. You would need an entirely different mount for that purpose, such as a wire rope mount.

I think your right in this case. The bobbins were meant to carry a load not the reverse. Thanks
Old May 18, 2012, 07:20 PM
timnilson is offline
Find More Posts by timnilson
timnilson's Avatar
Quote:
Originally Posted by Orracle View Post
The bobbins are being used correctly in this case, they must always be used under compression, not suspension. You would need an entirely different mount for that purpose, such as a wire rope mount.

This is a great diagram! Thanks for sharing!
Site Sponsor


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
New Product GOPRO FPV Spider Quadcopter V4.0 + Anti Virbation Mount (NEW Pics Updated 15Apr2012) DiVidesign Multirotor Talk 98 Nov 05, 2013 06:12 AM
New Product New from fpvmanuals: Lipo Strap made by Scorpion timnilson Multirotor Talk 9 Apr 27, 2012 12:41 AM
Wanted FPVmanuals tricopter lower main frame flohio117 Aircraft - Electric - Multirotor (FS/W) 2 Apr 02, 2012 11:35 PM
Discussion New GoPro lens protection product by fpvmanuals timnilson Aerial Photography 0 Dec 15, 2011 11:34 PM
Sold HobbyKing Quadcopter Frame V1 - NEW - $22.50 shipped Merkin77 Aircraft - Electric - Multirotor (FS/W) 3 Sep 30, 2011 01:55 AM