Taboo GT Bulkhead - RC Groups
Thread Tools
Apr 30, 2012, 01:50 PM
Duane, LSF IV
Wazmo's Avatar

Taboo GT Bulkhead

Does anyone have a measured drawing, template, or plan-view photo of a Taboo GT bulkhead (the one just ahead of the wing, where the pins insert)? Mine is broken, and the top half is missing. I can try using a contour gauge to duplicate the shape of the pod, but it would be nice to start with the correct size and shape.

Sign up now
to remove ads between posts
Apr 30, 2012, 02:00 PM
Registered User

I had three (3) Taboos (and often wish I still had one). Trust me on this: the top half is NOT repeat NOT critical in shape.

My recommendation: remove (if you haven't already) the bottom half, use it to rough out a new outline on new plywood and make a new replacement bulkhead. The original was designed to fit closely on the bottom, only.

If you do not wish to remove the bottom half, that's OK, too. I broke one of mine and made a rough-shape second one, and glued it to the back side of the remainder of the original. I drilled the initial holes a bit too small, then enlarged them with a round file to match the wing posts. In retrospect, it would have been easier to pull the old one out, and make a new one.

Good luck!

Yours, Greg
Apr 30, 2012, 02:55 PM
Auger up & out, not down & in!
IDOF3K's Avatar
Wasmo, I am currently putting my Taboo GT together using a windworks fuselage( long skinny thingy) . I have a complete fuselage and parts that you can have including a ballast system all brand new! PM me a reasonable offer and I will ship it to you. Tom
Apr 30, 2012, 04:11 PM
The ground's the limit.
shawnc's Avatar
I had this same problem last week. I cut up a piece of paper board until it fit the fuselage and under the canopy, then traced its outline onto my bulkhead stock (thin ply/balsa/ply-didn't have the stock plywood). A little finish sanding gave a like new fit.
Apr 30, 2012, 06:55 PM
Walter Roos
ROOSWH's Avatar
Scanned it, let's see how it looks

Comes out a tad small on my screen. Need to blow it up to 28x20mm

Right click on the small picture, click print and you get a big picture which you can reduce on most copy machines etc.

Last edited by ROOSWH; Apr 30, 2012 at 07:02 PM.
Apr 30, 2012, 06:58 PM
Duane, LSF IV
Wazmo's Avatar
Fantastic. Thanks, Walt.

@IDOF3K: Thanks for the offer. I'll keep that in mind as I evaluate the remaining repairs.
May 01, 2012, 12:32 AM
Duane, LSF IV
Wazmo's Avatar
The remaining bulkhead was glued with something rubbery and very tenacious, probably Goop. Finally got it out after much pulling, twisting, and cutting.

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Sold Taboo GT DLG BNF $460 SHIPPED Conus bcucoach2 Aircraft - Sailplanes (FS/W) 7 Apr 13, 2012 07:19 AM
Sold Taboo GT DLG BNF $460 SHIPPED Conus bcucoach2 Aircraft - Sailplanes (FS/W) 6 Apr 11, 2012 07:35 PM
For Sale Taboo GT DLG 225$ Angus540t Aircraft - Sailplanes (FS/W) 5 Mar 14, 2012 08:32 PM
Question Taboo GT Bulkhead Outline wamdue Hand Launch 2 Jun 04, 2009 05:48 PM
Discussion Taboo GT front bulkhead material D_Ryan Hand Launch 3 Sep 04, 2008 03:30 PM