Frsky X12D radio - Page 91 - RC Groups
Thread Tools
Jan 03, 2013, 12:12 PM
A10FLYR's Avatar
With 0 to 15 F temps we have had here the last week I have seen no problems with at least 15 different FrSky RXs used by different people I would not worry about that. Do the refridgerator test if you feel the need.
Sign up now
to remove ads between posts
Jan 03, 2013, 01:26 PM
Registered User
R_Lefebvre's Avatar
Originally Posted by Atomic Skull
If Futaba offered a 6 channel radio with the same kind of display as the DX6i I'd be all over that. I have no use for their advanced radios because most of the setup on a flybarless helicopter is on the gyro and not the radio. Subtrims, endpoints and CCPM is all done by the FBL controller. Hell they could even move the throttle and pitch curves into the gyro and let you fly on a 5 channel plank radio if they wanted to do that. That would actually be a pretty cool feature, you'd just set a linear throttle curve so the FBL controller could see the position of the collective stick. Then you could do your entire setup on the gyro over a PC or a smartphone.
Interesting you mention that... that is basically what I'm doing for helicopter in Arducopter. You hardly do anything in the radio, and you actually do fly an airplane profile. The only thing I set in the radio is some Expo.
Jan 03, 2013, 01:28 PM
Registered User
R_Lefebvre's Avatar
BUT the low temperature problems with the receivers worries me I would have hoped they would have srcreened that sort of failure out prior to despatch.
Woah, what is this about? I fly FrSky Rx's, in cold temps, never noticed anything.
Jan 03, 2013, 03:04 PM
Flying a Chipmunk in Portugal
jhsa's Avatar
Check this link and go 1 or 2 pages back. someone had problem with 2 receivers and cold apparently. I left a D8R-II Plus in the freezer for about 15 minutes and had no problem.. I think frsky will look into it..
Jan 03, 2013, 05:02 PM
Registered User
Originally Posted by scott page
Other than Futaba, what "major brand" would you consider as being a benchmark for quality?
JR and Hitec from experience, Airtronics and Multiplex by reputation. The original Spektrum from experience, but they were JR chassis. Cannot comment on the newer Spektrum and don't want to get into a religious war over it!
Jan 03, 2013, 05:10 PM
Proud member of LISF and ESL
I fly Futaba so that would be my benchmark. I think they make great gear. A bit pricy but good stuff.
I used to own Hitec and found their quality to be very high as well. Would buy Hitec again without hesitation.

However a key factor is the after sale service. If I break it can I get it fixed? Both Hitec and Futaba have provided me with outstanding after sale service.

With something like a Turnigy 9X or a 9XR, If you break it, maybe you just throw it away and get another because they are so cheap.

I don't know what the pricing of an X12D will be like but after sale service is important to me and part of that "quality" question.
Last edited by aeajr; Jan 03, 2013 at 05:19 PM.
Jan 03, 2013, 06:01 PM
Flying a Chipmunk in Portugal
jhsa's Avatar
buy it from alofthobbies and I'm sure they will take care of you..
Jan 03, 2013, 07:33 PM
Rotozuk's Avatar
Originally Posted by jhsa
buy it from alofthobbies and I'm sure they will take care of you..
FrSky will have a very satisfactory solution for any transmitter repairs. I'll let them announce the details when they are ready.

Yes, Aloft will continue to stand behind everything we sell.

Jan 03, 2013, 07:42 PM
Registered User
Atomic Skull's Avatar
Originally Posted by Kilrah
1 for me too.
All I need is:

Gyro gain switch - three position is nice but I've never needed more than one setting for heading hold and one for rate mode so 2 position is all that is required.

Throttle hold switch

DR switch(es), bonus if I can set elevator and aileron DR to a single switch.

Two or three position idle up switch (as with gyro gain three position is nice but 2 is all that is actually required)

A good set of gimbals.

Originally Posted by Rotozuk
FrSky will have a very satisfactory solution for any transmitter repairs. I'll let them announce the details when they are ready.

Yes, Aloft will continue to stand behind everything we sell.

That's the main reason I looking to replace my Devo 8, the gimbals have gotten a little creaky and once it's out of warranty (such as it is, this is Walkera after all) there's pretty much no way to get it fixed, they won't even sell me the gimbals to fix it myself. Walkera makes nice radios that work well but you won't be using them for years to come because when the sticks wear out Walkera expects you to throw it out and buy a new one.

It's a shame because some of Walkera's stuff is pretty well engineered, it's just that the quality control is often lacking and you get almost no customer support. They have the potential to be a great RC hobby company but they keep throwing it away.
Last edited by Atomic Skull; Jan 03, 2013 at 08:07 PM.
Jan 03, 2013, 07:44 PM
Suspended Account
Last edited by DoctorX; Jan 03, 2013 at 09:11 PM.
Jan 03, 2013, 07:50 PM
Registered User
stevea3342's Avatar
This looks like the main board from the 9xr.
Did you intend to post this in the x12d forum?
Jan 03, 2013, 08:06 PM
Rookie in training, heads up
efx's Avatar
Here's an interesting radio. It would be cool if they add an fpv on top of this radio you guys keep talking about. I think the fpv screen on the top would work better, but an all in one is pretty cool. Just throwing some more ideas for the frsky tx.
Jan 03, 2013, 09:02 PM
Registered Loiterer.
KC's Avatar
Originally Posted by DoctorX
I inverted the polarity of 7.2V battery and the little yellow part (picture below) of a TFR8S receiver got burned now I'd like to solder a new one, what's the name and price ?
I think the reference is 226C /60C73 is this correct ?
Here are a couple of posts that may help you.
Jan 03, 2013, 09:18 PM
Suspended Account
thanks KC I was reading the same thread it's a tantalum capacitor.
I need to replace it but I'm not sure if the receiver will survive because I was "playing" with
these are the numbers printed on 226C /60C73 if this is correct, what's the part number/manufacturer ?

Jan 03, 2013, 09:26 PM
Tassie Electric, Heli, Glider
ChrisJ800's Avatar
Getting back on topic, the Microtechnics site is listing the X9D availability as March.

and X12D Q2/2013.

Are they guessing or do they know something we dont? It looks like X9DA designation is for the prototype sets with cheap gimbals, but X9D production version will be BB gimbals which is nice (though prob wont help my low standard of flying!).

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Frsky X12D renatoa Romania 22 Mar 15, 2013 06:01 AM
Cool FrSky Radio Sale Rotozuk Hot Online Deals 95 Apr 04, 2012 08:08 PM
Discussion New radio to go with FrSky Teamsherman Australia 37 Mar 28, 2012 06:36 AM
Sold FlySky 9x TH9X radio w/ FrSky Telemetry Module and 2s 1300 battery. NEW! JIMinKENTUCKY Aircraft - General - Radio Equipment (FS/W) 1 Feb 25, 2012 07:08 PM
Discussion Ordering a new radio setup, 9x + frsky telemetry, am I missing anything? carl1864 Radios 8 Nov 28, 2011 11:53 PM