Thread Tools
Old Apr 12, 2012, 04:51 AM
zaguruinzasky is offline
Find More Posts by zaguruinzasky
Smoke on , go !
zaguruinzasky's Avatar
Discussion

Graupner MX-20 Failsafe problem


Guys I have a problem withthe mx-20

I'm using it for a mikrokopter, my receiver is the GR-32 (4 antennas), and the connection to the mikrokopter is via SUM channel (single cable).

I set the failsafe as described in the manual, selecting POS (position) for all channels, then I press SET and I get the message "Position Stored". But nothing happens if I turn off the radio. What is the problem ?

Thanks
Sign up now
to remove ads between posts
Old Apr 09, 2014, 06:05 PM
Mironb is offline
Find More Posts by Mironb
Registered User
I think you have the newest firmware in gr-32 which doesn't work with mirkokopter failsafe properly. I have the same problem. In others receivers I downgraded the firmware in gr-32 I can't do that I don't know why
Old May 16, 2014, 10:17 PM
glmccready is offline
Find More Posts by glmccready
Gary
glmccready's Avatar

A new message in an old thread!


I just bought two new GR-24L, and updated the Firmware, to 3.78 from 3.76. Neither of these work with Mikrokopter. When I shut off the Tx the MK still shows full transmitter strength!
I have an oler Gr-24L with 3.75 which works fine. Now if Ican just figure out how to load the old firmware? Update Assistant won't me.
Old May 19, 2014, 05:07 AM
glmccready is offline
Find More Posts by glmccready
Gary
glmccready's Avatar
Mikrokopter repsonds:
Graupner did change the FailSafe function in the receivers. If you use the latest Software on your receiver you have to go into the Menue "Setting & Data view".
There go to the window "RX Fail Safe Vx.xx" and change the "MODE" of channel 1 to "OFF". Now the copter will again receive the lost signal.

Mit freundlichen Grüßen / Best regards

Lothar Freudenberg

HiSystems GmbH
Last edited by glmccready; May 19, 2014 at 10:17 AM.
Old Mar 31, 2015, 04:29 PM
Mironb is offline
Find More Posts by Mironb
Registered User
That will not repair the failsafe fully. When you will first switch on the receiver (before transmitter failsafe wont work
Old Apr 11, 2015, 04:43 AM
janooo is offline
Find More Posts by janooo
Registered User
Quote:
Originally Posted by Mironb View Post
That will not repair the failsafe fully. When you will first switch on the receiver (before transmitter failsafe wont work
I have 3.78 and it doesn't work at all. Even if I switch on transmitter first.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Help! Graupner MX-16 problem esbakke Radios 3 Oct 27, 2012 02:30 PM
Discussion Graupner MX-20 HoTT exteng Radios 5 Apr 12, 2012 04:50 AM
Discussion SETUP FAILSAFE or ELSE - It flew away and I can't find it :( LifePo dies on MX-20 Mactadpole Aerial Photography 5 Apr 11, 2012 10:29 PM
Help! Graupner MX-16 or MX-20 HoTT urgent question!! bikertje888 Radios 2 Jan 24, 2012 08:50 AM
Discussion Graupner MX 20 and jets Henrique Lang Radios 2 Jan 23, 2012 09:36 AM