Thread Tools
Old Oct 02, 2012, 03:47 PM
Aussie John is offline
Find More Posts by Aussie John
Registered User
Hi All

What receivers will work with a Turnight 9x TX?. Full range models. The standard RX has that "heavy" aerial that has broken on me in a not so heavy arrival.

I replaced it with a standard aerial but no joy.

Can't tell if there is other damage to the RX. No physical damage. After soldering I ensured that the new aerial was not shorted.

I pulled apart the damaged aerial and it is a piece of brass tubing with a plug in one end soldered to the aerial. This is IMHO forms an open circuit stub. ie wave guide theory. Any comments?

My first question is my main concern and I would like to know what other folks are using in the way of receivers with the 9x tx

Thanks for any input.

Cheers jq
Sign up now
to remove ads between posts
Old Oct 02, 2012, 04:21 PM
Mr_McGlue is offline
Find More Posts by Mr_McGlue
Registered User
Mr_McGlue's Avatar
I only use the turnigy 8 channel ones from hobbyking. Had some problems with the 6 channel so just stuck with what works. If I order something from HK then I'll usually add a couple of them as they are usually around $9 each.
Old Oct 02, 2012, 10:06 PM
shahram72 is offline
Find More Posts by shahram72
Registered User
I and many others use these 6channel Rx's. Cheap and tiny. No problems. I have them in two airplanes.

http://www.hobbyking.com/hobbyking/s...dproduct=12901
Old Oct 03, 2012, 11:06 AM
dave1993 is offline
Find More Posts by dave1993
RC beginner
also note that they have ppm out which even many expensive rx lack. the 3ch were my favorite but price has doubled and if i need 4ch the 6ch is next best thing.
Old Oct 03, 2012, 11:31 AM
Mr_McGlue is offline
Find More Posts by Mr_McGlue
Registered User
Mr_McGlue's Avatar
Those were the ones I had a problem with. I use them in my smaller planes/foamies and seem to be ok. Just don't trust them after two different model crashes.

Robert

Quote:
Originally Posted by shahram72 View Post
I and many others use these 6channel Rx's. Cheap and tiny. No problems. I have them in two airplanes.

http://www.hobbyking.com/hobbyking/s...dproduct=12901
Old Oct 03, 2012, 11:47 AM
aeajr is offline
Find More Posts by aeajr
Proud member of LISF and ESL
Quote:
Originally Posted by dave1993 View Post
also note that they have ppm out which even many expensive rx lack. the 3ch were my favorite but price has doubled and if i need 4ch the 6ch is next best thing.
What does this mean? PPM out?
Old Oct 03, 2012, 12:50 PM
dave1993 is offline
Find More Posts by dave1993
RC beginner
ppm stands for pulse position modulation and is a combined version of the servo and esc signals that only need 1 pin instead of many. not so much for planes but very useful for multicopters and uavs where bulky cables are a problem.
Old Oct 03, 2012, 12:54 PM
renatoa is offline
Find More Posts by renatoa
Registered User
old style s-bus
Old Oct 03, 2012, 02:21 PM
aeajr is offline
Find More Posts by aeajr
Proud member of LISF and ESL
Quote:
Originally Posted by dave1993 View Post
ppm stands for pulse position modulation and is a combined version of the servo and esc signals that only need 1 pin instead of many. not so much for planes but very useful for multicopters and uavs where bulky cables are a problem.
I know PPM as a signal enoding within the transmitter that is used ot transmit the information to the receiver. Are you saying you are tapping into the PPM stream for something new? Otherwise, plugging a servo into the receiver gives you access to the PPM stream for servo commands. Pretty much all receivers do that.
Old Oct 03, 2012, 03:43 PM
dave1993 is offline
Find More Posts by dave1993
RC beginner
servos cannot use ppm. they need pwm which requires a separate pin for each signal. ppm is a combined version of the servo and esc signals that only need 1 pin instead of many. usually an mcu is what connects to ppm. google is your friend.
Old Oct 03, 2012, 03:45 PM
aeajr is offline
Find More Posts by aeajr
Proud member of LISF and ESL
you learn something new every day.
Old Oct 03, 2012, 03:47 PM
renatoa is offline
Find More Posts by renatoa
Registered User
This drawing may help even more:

Old Oct 06, 2012, 10:42 PM
baconflyer is offline
Find More Posts by baconflyer
cheapskate extroardinairé
Quote:
Originally Posted by Aussie John View Post
Hi All

What receivers will work with a Turnight 9x TX?. Full range models. The standard RX has that "heavy" aerial that has broken on me in a not so heavy arrival.

I replaced it with a standard aerial but no joy.

Can't tell if there is other damage to the RX. No physical damage. After soldering I ensured that the new aerial was not shorted.

I pulled apart the damaged aerial and it is a piece of brass tubing with a plug in one end soldered to the aerial. This is IMHO forms an open circuit stub. ie wave guide theory. Any comments?

My first question is my main concern and I would like to know what other folks are using in the way of receivers with the 9x tx

Thanks for any input.

Cheers jq
good tip: slide a drinking straw over the aerial and hot glue it to the receiver. this prevents it from ripping off in a crash.
Old Oct 06, 2012, 11:51 PM
hoghead5150 is offline
Find More Posts by hoghead5150
The wind caused that!!
hoghead5150's Avatar
so is there any updates on when the new 9xr transmitter will be released??
Old Oct 07, 2012, 07:38 AM
kgfly is offline
Find More Posts by kgfly
Registered User
Why ask? If there was an update it would have been posted and you would have read it. Nothing posted means no update. Pretty simple really.


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Gens Ace, Turnigy, Turnigy Nano-Tech Sky lipo, etc. What's Your Preference? jlloyd1995 Batteries and Chargers 133 May 14, 2015 11:53 PM
Sold 2 turnigy motors 2 turnigy esc's crashnburn69 Aircraft - Electric - Power Systems (FS/W) 4 Oct 13, 2012 12:05 PM
For Sale Turnigy 2x 3s 1000 mah and 2s 1000 mah and Turnigy 2s/3s Lipo charger. Falconpunch Aircraft - Electric - Batteries & Chargers (FS/W) 1 Mar 18, 2012 10:47 PM
Discussion Turnigy or Turnigy Nanotech lawguy14 Batteries and Chargers 4 Mar 15, 2012 09:48 AM