Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Feb 17, 2013, 02:38 PM
juraj.jurej is offline
Find More Posts by juraj.jurej
Registered User
How to revamp gas ratchet?
Sign up now
to remove ads between posts
Old Feb 17, 2013, 04:35 PM
gooby is offline
Find More Posts by gooby
hjukhjuk
gooby's Avatar
Quote:
Originally Posted by juraj.jurej View Post
How to revamp gas ratchet?
Paint it red?
Old Feb 17, 2013, 04:41 PM
pmackenzie is offline
Find More Posts by pmackenzie
I don't want to "Switch Now"
pmackenzie's Avatar
Quote:
Originally Posted by juraj.jurej View Post
How to revamp gas ratchet?
Quote:
Originally Posted by kovs View Post
Paint it red?
I think he meant how to get the ratchet action on the throttle to be better

Open it up and bend/adjust the metal tensioner.
RCG Plus Member
Old Feb 17, 2013, 05:04 PM
juraj.jurej is offline
Find More Posts by juraj.jurej
Registered User
Quote:
Originally Posted by pmackenzie View Post
I think he meant how to get the ratchet action on the throttle to be better

Open it up and bend/adjust the metal tensioner.
Yes I think so. Sorry I'm from Slovakia
Old Feb 17, 2013, 05:04 PM
lvclimber is online now
Find More Posts by lvclimber
Registered User
Quote:
Originally Posted by LowThudd View Post
As stated, this is a known issue. Some have separated the wires, and some have simply glued the connector. You'll have to open it up and see what is going wrong with the gimbals.
Thanks for the info LowThudd, however the gimbal appears to be working fine...no binding and it's centered. It's the actual shaft that looks like if was assembled incorrectly. I'm not sure if they are pressed in but it looks like it was pushed in crooked. So can see in the picture that the gimbal is actually centered but the shaft looks bent.

Any idea if the threaded shaft comes out easily?
Old Feb 17, 2013, 06:13 PM
airheli1201 is offline
Find More Posts by airheli1201
Registered User
I wonder if there will be a back stand available for the 9XR soon? it's really awkward that you can't lie the 9xr on it's back without putting stress on the tx module.
Old Feb 17, 2013, 06:22 PM
thekesh is offline
Find More Posts by thekesh
Registered User
Quick question, when I try to unscrew the screws in the back some of the screws come off but the rest just spin but dont come off. Is anyone else experiencing similar problems?
Old Feb 17, 2013, 06:24 PM
kenstogie is offline
Find More Posts by kenstogie
Embargo lifted.
kenstogie's Avatar
I finally installed the USBasp drivers, eepe(?) and flashed the 9xr with the latest er9x firmware. Piece of cake thank to the utube video. Its on the tutorial thread if you need it. At this point I am just playing around trying to figure out the menus and buttons and so forth. Some time very soon I will glue down my gimbal connectors. The lead (as others have noticed) seem to "see saw" on the connector. Probably would be fine but I can crash without any help from a tx, thank you very much. LOL
Old Feb 17, 2013, 06:25 PM
kenstogie is offline
Find More Posts by kenstogie
Embargo lifted.
kenstogie's Avatar
Quote:
Originally Posted by thekesh View Post
Quick question, when I try to unscrew the screws in the back some of the screws come off but the rest just spin but dont come off. Is anyone else experiencing similar problems?
I just did that too mine seem to be fine, except they didn't want to come out of the back of the tx even though they did back out completely from the front part. If that makes any sense. Once the back came off I could poke something in the screw hole to remove them.
Old Feb 17, 2013, 06:35 PM
abletowinginc is offline
Find More Posts by abletowinginc
Lets make it remote control!!!
abletowinginc's Avatar
Quote:
Originally Posted by barok View Post
jus a heads up.. not sure if it has been mention..

got the HT to work via aka. futaba square plug.. it seems that pin 6 (signal in) is not connected..bad HK.... work around is to solder pin6 to pin3, a jumper...

this will fix also your uhf module to work on this square plug..

btw.. i hacked the jr plug (not to be use as a trainer) to power my 2.4ghz amp/booster.. looks neater..
so will this work to power the fatsharkgoggles?will voltage be safe that comes out?
Old Feb 17, 2013, 07:03 PM
LowThudd is offline
Find More Posts by LowThudd
Registered User
Quote:
Originally Posted by airheli1201 View Post
I wonder if there will be a back stand available for the 9XR soon? it's really awkward that you can't lie the 9xr on it's back without putting stress on the tx module.
This might work http://www.helipal.com/airy-transmitter-holder.html
Old Feb 17, 2013, 07:14 PM
iggy809 is offline
Find More Posts by iggy809
Registered User
started looking for a TX. Turnigy 9X ebay around $100. Flysky 9x ebay $100. Hobby king 9x $78. Are these the same and is HK the way to go.
Old Feb 17, 2013, 07:19 PM
gooby is offline
Find More Posts by gooby
hjukhjuk
gooby's Avatar
Quote:
Originally Posted by iggy809 View Post
started looking for a TX. Turnigy 9X ebay around $100. Flysky 9x ebay $100. Hobby king 9x $78. Are these the same and is HK the way to go.
Never buy hobbyking products from ebay or amazon, you will get ripped off each time. The 9X is also a different radio than the 9XR which this thread is about.
Old Feb 17, 2013, 10:13 PM
Mikarro is offline
Find More Posts by Mikarro
Suspended Account
A9 gimbals still available.... http://www.robotshop.com/axis-joystick-gim.html
Old Feb 17, 2013, 10:25 PM
mpjf01 is offline
Find More Posts by mpjf01
Registered User
mpjf01's Avatar
Quote:
Originally Posted by Mikarro View Post
A9 gimbals still available.... http://www.robotshop.com/axis-joystick-gim.html
After April 8


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Gens Ace, Turnigy, Turnigy Nano-Tech Sky lipo, etc. What's Your Preference? jlloyd1995 Batteries and Chargers 133 May 14, 2015 11:53 PM
Sold 2 turnigy motors 2 turnigy esc's crashnburn69 Aircraft - Electric - Power Systems (FS/W) 4 Oct 13, 2012 12:05 PM
For Sale Turnigy 2x 3s 1000 mah and 2s 1000 mah and Turnigy 2s/3s Lipo charger. Falconpunch Aircraft - Electric - Batteries & Chargers (FS/W) 1 Mar 18, 2012 10:47 PM
Discussion Turnigy or Turnigy Nanotech lawguy14 Batteries and Chargers 4 Mar 15, 2012 09:48 AM