Show Us Your Hoverthings FPV Frame - Page 99 - RC Groups
Thread Tools
Nov 07, 2012, 02:22 AM
Registered User
Hi everyone, I have had an HT-FPV sitting in my garage waiting for me to finish it. I have 25a plush esc's for it and motors from hoverthings but I'm thinking I need larger/stronger motors to lift it with full FPV gear. What motors are recommended?. I plan on using 3s batteries.
Sign up now
to remove ads between posts
Nov 07, 2012, 11:07 AM
p0st4L's Avatar
What size motors do you have? I personally use 980KV motors on a 3S w/ 10"x4.5" props and it works just fine.
Nov 07, 2012, 11:35 AM
q {bld(); fly(); brk(); q();}
The Recursion's Avatar
I'm the same as postal, but you should learn how to use this site and input different combinations. Everyones setup is different, and before making a decision you should know why you've made it.
Nov 10, 2012, 02:39 AM
Custom quad builder
tech69x's Avatar
Hello all this is my new ht- fpv with sunnysky 980 kv motors 9 in props 4s 2200 mah battery EZosd with fat shark predator with a cc3d FC
Nov 10, 2012, 11:50 AM
Fly safe, fly often!
Buzz_Man's Avatar

I added some 600 size heli landing gear I found collecting dust in my shop.

This provides a nice "cushion" between the grass and the camera & battery (I mount my batteries on the bottom).

Happy flyin'

Nov 10, 2012, 10:05 PM
theSouthGA's Avatar
Looks good guys!
I just had the opportunity to get video of hot air ballons here in south GA. I was going to fly my QAV but for some reason it was acting squirrely yesterday and being that I was in relatively close proximity to the ballons I opted out of that platform. but... the HT FPV pulled through like a champ! I'll try to get some video up later. I was lucky enough to get permission from the event coordinators to fly after briefing the balloon pilots. I was freaking elated! Here is a pic from yesterday afternoon. My setup info is posted earlier in this thread. I have since upgraged to the T Motors 900kv. I run them on 3s, 3800's w/10x4.7props.
Nov 11, 2012, 10:13 AM
Nice shot, hope to see some video and get some up myself.
Nov 11, 2012, 12:26 PM
Registered User

My first quadcopter

Please have a look at my first quadcopter build, here is the link to the video, please post any improvements you could make.

quadcopter indoor/outdoor flight kk 2.1 (3 min 19 sec)

My next build is going to be with the sk 450 or the x550 frame, i am making these with an extremely stable kk2 board so if anyonw want to buy im selling extremely cheap 400 so if ur interested post below my youtube video many people are happy for this offer so reply soon.
Nov 11, 2012, 05:19 PM
theSouthGA's Avatar


Here is a link to the video. Its just something I put together "quickly" but I'll polish up the footage later.

Blue Skies!

Harmony (7 min 20 sec)
Nov 11, 2012, 05:36 PM
Registered User
EddieWeeks's Avatar
6 motor tri-copter...

Nov 12, 2012, 05:35 AM
Fly safe, fly often!
Buzz_Man's Avatar
LINK (short LOS video - flying in my yard)
Nov 12, 2012, 08:04 AM
Registered User
Boris B's Avatar
I did a rebuild of mine

Nov 12, 2012, 08:33 AM
theSouthGA's Avatar
Thats nice Garbungle! how did you get your PDB wiring to fit in the lower plate with the NAZA in there?
Nov 12, 2012, 09:00 AM
Registered User
Boris B's Avatar
I wanted to have minimum weight possible on this build. That's why I decided to remove power distro board and the top plate.
I actually just soldered all ESC's with battery connector together and put everything neatly in between. There is plenty of room actually when you don't use the power distribution board.
Nov 12, 2012, 07:14 PM
theSouthGA's Avatar
Thats a 10-4 garbagungle! I was considering that option but i chose to put my rx and fc on the second plate. It was easier for me to set everything up afterward but I think yours is probably the most efficient I've seen (space wise). Good job anyways. I dont think I could fit all my stuff in there even if the PD stuff was on the second plate up. The arms stick in there so far. I went in and shortened some wires and braided and twisted some things after the initial setup but thats it.

are those 8" Graups on 3s too?

Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Show Us Your Ground Station !!!! FPV Ground Station Design and Idea's found here :) JettPilot FPV Equipment 4879 Nov 03, 2017 11:44 PM
Discussion Show us your FPV Multicopter Derek_S FPV Talk 194 Feb 08, 2013 01:07 PM
Discussion FPV Successful? Show us setup and parts list Royalson FPV Talk 0 Mar 10, 2012 09:25 AM
Discussion Show us your FPV / RVP ground Base set up in action Trackercal FPV Talk 94 Nov 05, 2010 11:21 AM
Discussion Show Us Your FPV Helo Set Up Trackercal FPV Talk 2 May 12, 2009 12:05 AM