Lumenier RB2205C-12 2400KV SKITZO Ceramic Bearing Motor
Thread Tools
Old Oct 13, 2012, 11:06 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
Quote:
Originally Posted by RC911 View Post
Be aware that those prop spinners may produce bad vibrations. I recommend replacing them with 5mm lock nuts.
I took your advice and replaced the spinners with 5mm lock nuts
Sign up now
to remove ads between posts
Old Oct 14, 2012, 11:59 AM
RC911 is online now
Find More Posts by RC911
8 bit is more fun
RC911's Avatar
Quote:
Originally Posted by Titus Gordon View Post
I took your advice and replaced the spinners with 5mm lock nuts
Did you do this because you noticed vibrations?
I've seen posts about this problem in other threads earlier.
Old Oct 14, 2012, 12:56 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
Honestly at this stage of my learning I wouldn't know a vibration from an oscillation

Seemed like a good idea though

Quote:
Originally Posted by RC911 View Post
Did you do this because you noticed vibrations?
I've seen posts about this problem in other threads earlier.
Old Oct 14, 2012, 01:42 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
Here's a recent pic after changing the spinners to lock nuts

Old Oct 14, 2012, 05:33 PM
RC911 is online now
Find More Posts by RC911
8 bit is more fun
RC911's Avatar
Quote:
Originally Posted by Titus Gordon View Post
Honestly at this stage of my learning I wouldn't know a vibration from an oscillation

Seemed like a good idea though
You would probably have noticed these vibrations as "jello" on your video recordings.
Old Oct 14, 2012, 05:50 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
yeah.

I don't have a HD camera yet, I've just been recording the wireless FPV video so far, got another one going up on youtube soon.

check it out

http://www.youtube.com/user/tr3jn
Old Oct 14, 2012, 06:54 PM
p0st4L is offline
Find More Posts by p0st4L
BUILD.FLY.CRASH.REPEAT.
p0st4L's Avatar
Still waiting for my OSD setup & LayerLens to get here so I can finish wiring and get this beast in the air.


http://imgur.com/eSUFb
RCG Plus Member
Old Oct 14, 2012, 09:47 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
p0st4L, nice quad

Here's today's flying, I'm really enjoying this!

FPV 14.10.2012 Getting to know the quad, Part II (7 min 18 sec)
Old Oct 15, 2012, 05:17 PM
RC911 is online now
Find More Posts by RC911
8 bit is more fun
RC911's Avatar
Quote:
Originally Posted by Titus Gordon View Post
yeah.

I don't have a HD camera yet, I've just been recording the wireless FPV video so far, got another one going up on youtube soon.

check it out

http://www.youtube.com/user/tr3jn
Not bad at all. Nice flying location also.
Old Oct 15, 2012, 05:49 PM
Titus Gordon is offline
Find More Posts by Titus Gordon
FPV it is!
Thanks! yeah the field is kinda neat
Old Oct 15, 2012, 06:51 PM
elliott000 is offline
Find More Posts by elliott000
Registered User
Finally getting back to my htfpv frame, i have some mt 2216-11 900 kv... Anyone tried em on here? I ran em for a day i think. Shoupd i bolt em back on itd be on 4s
Old Oct 15, 2012, 07:45 PM
flitelab is offline
Find More Posts by flitelab
flitelab's Avatar
I use and sell the Tiger motors, 2216s will be a good fit on that frame, I used then on a custom ht-fpv frame build with wkm. With 4s you will probably need to go 8" props, I had the custom build on 3s with 10".

Some pics, video and info. http://www.flitelab.com/Reviews/HTFPVFrameOverview.aspx
Site Sponsor
Old Oct 16, 2012, 12:10 PM
mstocker is offline
Find More Posts by mstocker
Middleton, Nova Scotia
Hi; First post to these forums I think, and have only been flying Quads (Hoverthings frames), since March, so you can take my comments from whence they come. : ). I am using these 2216-900kv T-motors also purchased from Mark@Flitelab, on the HT-FPV. I really like the responsiveness with 4s and 9x5 Graupner E-props, using 3 to 3.3A Batts. Carrying just a GoPro, the rig hovers at about 40-42% with lottsa pop, and seems to work better in breezy, windy conditions.
Using 3s, 3 to 3.3A Batts. and 10x5 Graups. or Gemfams, I don't see a lot of difference in performance, but it seems mebbe a wee bit more loose and a tad more floaty in the wind.
The Graups. with these motors, are really smooth and allow a very good Vid. just about jello free using 1080HD.
Hope this helps...Matt
Old Oct 16, 2012, 10:11 PM
theSouthGA is offline
Find More Posts by theSouthGA
KK4LIK
theSouthGA's Avatar
I just posted 2 videos on the last page that shows the difference between DJI 920's and the 2216-11 900's on the last page. Both were running 10" slow fly props on 3s though. No matter what motor you choose be sure to balance your props, it can make all the difference.
Old Oct 20, 2012, 06:06 PM
Kosmos is offline
Find More Posts by Kosmos
Just Starting..

First build


This is my first quad - very new to ALL this, but I am very excited to get this in the air - still waiting on ESCs, and other things.....
My plan is a HTFPV frame with:
-Eagletree OSD and logger and GPS,
-ImmersionRC 5.8 vTX
-GoPro flight record
-readymaderc - RMRC-540N video for FPV
-Turnigy plush 30A ESC
-3300mah 3S main lipo
-500mah 3S vTX lipo
-28-26A motors (had to cut the shafts)
-DJI NAZA with GPS
-Eagle tree ground station (readymaderc tracking station)
-Fat Shark goggles

Some suggests most welcome on my wiring diagram I know it is not right - little confusing to a newbie. I also got power distribution plate from HT would like ask for some guidance as how best to solder that up? Would I be better off
with a 750mah for video system? Question on GS - how best to wire up the lipo there would like a dual 5000mah setup - is it best to use a regulator there?
I'll be powering the tracking station and servos, 5.8 video receiver, fat sharks, and perhaps a small LCD of some sort - still working on that idea....
One last thing - how best to power the FPV camera?

Draft Wire Diagram


Ground Station under construction:


Cut down the 28-26A motor shafts:


Shaft almost flush with the motor - but there is room with the motor mounts anyway:


Arms are done and Body shafts installed - I CA'd the motor mounts - hope I don't regret that...


In the mean time I am abusing an MQX quad - to brush up on my flight skills and
get myself comfy with the Specktrum DX8.

TIA


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Show Us Your Ground Station !!!! FPV Ground Station Design and Idea's found here :) JettPilot FPV Equipment 4632 Dec 08, 2016 04:47 AM
Discussion Show us your FPV Multicopter Derek_S FPV Talk 194 Feb 08, 2013 01:07 PM
Discussion FPV Successful? Show us setup and parts list Royalson FPV Talk 0 Mar 10, 2012 09:25 AM
Discussion Show us your FPV / RVP ground Base set up in action Trackercal FPV Talk 94 Nov 05, 2010 11:21 AM
Discussion Show Us Your FPV Helo Set Up Trackercal FPV Talk 2 May 12, 2009 12:05 AM