Show Us Your Hoverthings FPV Frame - Page 106 - RC Groups
Thread Tools
Nov 24, 2012, 07:48 PM
'FPV'er...not a "LOS'er
Vantasstic's Avatar
Quote:
Originally Posted by scrape
I think I pushed the battery to far. Think I'll keep it closer to the ground @ the end of the pack.
It's official...you broke it!!!
Sign up now
to remove ads between posts
Nov 24, 2012, 08:09 PM
Gary
glmccready's Avatar
scrape: bummer. I never let my lipos get to low. Good thing you had those led light strips to hold it all together!
Nov 24, 2012, 08:13 PM
Custom quad builder
tech69x's Avatar
Quote:
Originally Posted by scrape
I think I pushed the battery to far. Think I'll keep it closer to the ground @ the end of the pack.
http://www.youtube.com/watch?v=2vi__gd84XI
Is That a sc2000 cam you are using if so how did you hook it up to the EZosd

Sorry about the crash
Nov 24, 2012, 09:07 PM
Quote:
Originally Posted by Vantasstic
It's official...you broke it!!!
Quote:
Originally Posted by glmccready
scrape: bummer. I never let my lipos get to low. Good thing you had those led light strips to hold it all together!


Quote:
Originally Posted by tech69x
Is That a sc2000 cam you are using if so how did you hook it up to the EZosd

Sorry about the crash
No, it a RMRC-600 they have a cable for plug & play hook-up. Thanks
Nov 26, 2012, 01:36 AM
Registered User
OK, I am going to move my Naza to this HT-FPV frame, have been using a CopterControl board. Question:

I'm using Turnigy Plush 30A esc, and currently I have only the signal wire (white) connected on 3 of 4 ports on the FC. All 3 wires (red, black and white) are connected on 1st port. Using the Naza FC do I need to reconnect all these wires again or does it matter, if all 3 wires are intact coming from the esc is that ok as well?

Just curious.
Last edited by shdwkeeper; Nov 26, 2012 at 01:44 AM.
Nov 26, 2012, 01:39 AM
Custom quad builder
tech69x's Avatar
Quote:
Originally Posted by shdwkeeper
OK, I am going to move my Naza to this HT-FPV frame, have been using a CopterControl board. Question:

I'm using Turnigy Plush 30A esc, and currently I have only the signal wire (white) connected on 3 of 4 ports on the FC. All 3 wires (red, black and white) are connected on 1st port. Using the Naza FC do I need to reconnect all these wires again or does it matter, if they are all 3 wires are intact coming from the esc is that ok as well?

Just curious.
Just one like the cc3d
Nov 26, 2012, 01:43 AM
Registered User
Quote:
Originally Posted by tech69x
Just one like the cc3d
If I have 4 brand new Turnigy 30a ESCs do I still need to remove the wires from them or can I leave them intact? I know with the DJI esc/motors you don't touch anything.
Nov 26, 2012, 01:51 AM
Custom quad builder
tech69x's Avatar
My bad you have to take all of the power wires off
Nov 26, 2012, 01:52 AM
Custom quad builder
tech69x's Avatar
I just looked at mine to be sure
Nov 26, 2012, 02:04 AM
Registered User
Quote:
Originally Posted by tech69x
I just looked at mine to be sure
you have a picture? So I only want the white wire connected on all the Plush 30A esc's to the naza then correct?
Nov 26, 2012, 02:05 AM
Custom quad builder
tech69x's Avatar
No the white and black
Last edited by tech69x; Nov 26, 2012 at 02:10 AM.
Nov 26, 2012, 02:07 AM
Multi rotors=No Paycheck left
SDSURFnGLIDE's Avatar
I use a Naza on mine and you only need to run the white signal wire...
Nov 26, 2012, 02:18 AM
Registered User
Quote:
Originally Posted by SDSURFnGLIDE
I use a Naza on mine and you only need to run the white signal wire...
Ok, I will remove all wires except the white one. You also have the Plush 30a esc as well right? I'm reading that some folks are having problems with this esc and they had to re-flash the firmware, hopefully i won't have to do that.
Nov 26, 2012, 02:23 AM
Custom quad builder
tech69x's Avatar
I have been using flashed esc's with no problem
Nov 26, 2012, 02:25 AM
Custom quad builder
tech69x's Avatar
You need to go here and ask

https://www.rcgroups.com/forums/show...0#post23363800


Thread Tools

Similar Threads
Category Thread Thread Starter Forum Replies Last Post
Discussion Show Us Your Ground Station !!!! FPV Ground Station Design and Idea's found here :) JettPilot FPV Equipment 4879 Nov 03, 2017 11:44 PM
Discussion Show us your FPV Multicopter Derek_S FPV Talk 194 Feb 08, 2013 01:07 PM
Discussion FPV Successful? Show us setup and parts list Royalson FPV Talk 0 Mar 10, 2012 09:25 AM
Discussion Show us your FPV / RVP ground Base set up in action Trackercal FPV Talk 94 Nov 05, 2010 11:21 AM
Discussion Show Us Your FPV Helo Set Up Trackercal FPV Talk 2 May 12, 2009 12:05 AM